User manual MARANTZ ST7001

[. . . ] Model ST7001 User Guide FM / AM Tuner CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · The frequency changes continuously when the TUNING button /1 on the remote control unit is held in. c v b TE EN R BAND A-PRESET /A-TUNE MENU SHIFT /2 /4 CHANNEL/ CONTROL A/B C/D E/F G/H I/J T-MODE /5 SLEEP TIMER MEMO REMOTE CONTROLLER RC7001ST 11 ENGLISH OPERATION OPERATION ENGLISH 7 Preset stations (FM/AM) 1. Use the "Auto tuning" or "Manual tuning" operation to tune in the station to be preset in the memory. 7 Recalling preset stations (FM/AM) 1. Press the POWER ON/STANDBY switch q or ON button , to turn on the power. 2. Press the MENU button u or /2 to select menu. Either turn the TUNING/PRESET knob !4 or press the CHANNEL/CONTROL button /4 to select "Memory". 2. Watching the display, press the BAND SELECT button !0 or BAND button c to select the desired band (AM or FM). 3. Press the MENU button u or /2 to select menu. 4. Press the TUNING/PRESET knob !4, or ENTER button v to set the preset mode and make the preset channel number flash. 4. Press the TUNING/PRESET knob !4 or ENTER button v to set search mode. 5. Either turn the TUNING/PRESET knob !4 or press the CHANNEL/CONTROL button /4 to select "Preset". · Steps 1 to 4 can be skipped when using the MEMO /6 button. When this button is pressed, the preset memory standby mode is set, regardless of the menu setting at that time. 6. Press the TUNING/PRESET knob !4 or ENTER v button and set the preset mode. 5. While the preset channel number is flashing, either press the SHIFT button /3 to select the desired memory group (A to J) or press a MEMORY GROUP (A to J) button n. 6. While the preset channel number is flashing, either turn the TUNING/PRESET knob !4, press the CHANNEL/CONTROL /4 or Preset channel button x to select the desired preset channel (1 to 10). 7-1. Watching the display, turn the TUNING/ PRESET knob !4, or press the CHANNEL/CONTROL button /4 to select the desired preset channel. 7. While the preset channel number is flashing, either press the TUNING/PRESET knob !4 or MEMO button /6 to store the station in the preset memory. · To preset other channels, repeat steps 2 to 6. · A total of 100 broadcast stations can be preset -- 10 stations (channels 1 to 10) in each of groups A to J. 7-2. Press the SHIFT button /3 and select the desired memory group (A to J) or press the MEMORY GROUP (A to J) button n. 7-3. Press the Preset channel button x to select the desired preset channel (1 to 10). Note · Steps 2 to 6 can be skipped when using the CHANNEL/CONTROL /4, SHIFT /3, MEMORY GROUP (A to J) n and Preset channel x buttons. The preset mode is set when any of these buttons is pressed, regardless of the menu setting at that time. 12 7 Registering station names (FM/AM only) 1. Use the procedure described at "Auto tuning", "Manual tuning" or "Recalling preset stations" to tune in the desired frequency. Example: To register "MARANTZ" as the FM station name at preset channel "A2". TUNING/PRESET FM/AM TUNER ST7001 STANDBY SLEEP TIMER TUNED STEREO POWER ON/STANDBY CATEGORY DISPLAY MENU A--PRESET BAND SELECT PUSH ENTER q ui !0 !4 2. Press the MENU button u or /2 to select menu. STANDBY ON , 3. [. . . ] · Batteries are not set in their proper direction (ª and ·). · Remote control code is different between the main unit and remote control. · Rear Panel EXTERNAL/INTERNAL switch is set EXTERNAL position. · XM terminal and the XM Connect-andPlay antenna is not properly connected. [. . . ]