User manual MARANTZ VP10S1

[. . . ] Model VP-10S1 User Guide DLPTM Projector CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. For the customers in the USA: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] To focus the pattern, press the 1 / 2 buttons on the remote controller or projector. Tapping the buttons fine-adjusts the focus. Holding the buttons down quickly changes the focus. Adjust the focus so that the focus pattern appears its sharpest, as shown below. 3. To adjust the size of the projected image, press the 3 / 4 buttons on the remote controller or projector. Tapping the buttons fine-adjusts the size. Holding the buttons down quickly changes the size. 4. Press the PATTERN button again to cancel the focus pattern. This completes focusing and zooming. 17 ENGLISH EN TE R PAT TER PAT TE N IN P UT ME NU NU PO WE PO R WE R Positioning the Projected Image You can position the projected image on the screen using the "Lens shift" feature in the menu (OSD). (For an explanation of this feature, see "Configuration"  pg. 32. ) First, project an image on the screen. (If you haven't an Input signal, display the focus pattern. ) PATT. 1. Press the MENU button on the remote controller or projector to display the menu. Select "Config" using the 3 / 4 buttons, then press the 2 button. Select "Lens shift" using the 3 / 4 buttons, then press the 2 button. (If you haven't an Input signal at this point, display the focus pattern. ) 4. Position the projected image vertically on the screen using the 3 / 4 buttons on the remote controller or projector. Upward Downward 5. Position the projected image horizontally on the screen using the 1 / 2 buttons on the remote controller or projector. To right ON STANDBY PATTERN INPUT MENU POWER ENTER ING Top view To left 18 WARN EN TE R PAT TE RN IN P UT ME S TA NU N PO D B WE Y R O N ENGLISH 1 1 2, 3, 4, 5 MENU V-MUTE ENTER 2, 3, 4, 5 INPUT ASPECT Side view WARN ING Keystone Correction ENGLISH If the projected image appears trapezoidal in shape, you can correct it using the "Keystone V" and "Keystone H" features in the menu (OSD). (For an explanation of this feature, see "Display"  pg. 31. ) PATT. 1 1 2, 3, 4 MENU V-MUTE 2, 3, 4 PAT TE RN IN P UT ME S TA 1. 4. Press the MENU button on the remote controller or projector to display the menu. Select "Display" using the 3 / 4 buttons, then press the 2 button. Select "Keystone V" or "Keystone H" using the 3 / 4 buttons, then press the 2 button. Correct in the vertical or horizontal distortion using the 1 / 2 buttons on the remote controller or projector. - Vertical keystone correction - ENTER WARNIN G Note : Horizontal keystone is best corrected when the projector is installed on a flat surface and the image is shifted to the maximum height using the "Lens shift" feature in the menu. NING WAR G EN T ER NU N PO D B WE Y R O N ENTER INPUT ASPECT - Horizontal keystone correction - ON BY STAND POWER MENU INPUT N PATTER NING WAR ENTER PATTER N WARNIN INPUT STAND MENU BY ON POWER 19 BASIC OPERATIONS ENGLISH Activating the Power 1. [. . . ] Press the MUTE button to release the mute. Make the distance between the unit and the remote control closer. Select the "INTERNAL" position. Initialize the sensor by taking the correct procedures. [. . . ]