User manual MARANTZ VP12S4

[. . . ] Model VP-12S4 User Guide DLPTM Projector ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. Install in accordance with the manufacture's instructions. [. . . ] When disposing of used batteries, please comply with governmental regulations or environmental public instruction's rules that apply in your country or area. VP-12S4 5m 7 ENGLISH CONNECTION When making connections be sure to: Turn off all equipment before making any connections. Use the proper cables for each connection. Securely insert the plug into the port to connect cables. Loose cables can lead to trouble and damage. Connection with Video Equipments You can connect this projector to a VCR, DVD player and other video equipment. ENGLISH Connecting a video source using S-VIDEO IN and VIDEO IN terminals. 1. 2. Connect one of the S-video cable to the S-VIDEO IN terminal, or one end of the video cable to the VIDEO IN terminal on the projector. Connect the other end of the S-video cable or the video cable to the S-video output terminal or video output terminal of the video source. When pulling out a cable: Be sure to grab the plug, not the cable itself. Connecting a DVD player to the COMPONENT VIDEO IN 1 or 2 terminal (Devices can be connected to both terminals at the same time. ) 1. 2. Connect the individual terminals of the component video cable into the COMPONENT VIDEO IN 1 or 2 terminal of the projector. Connect the other end of the cable to the corresponding terminals on a DVD player. Connection with AC Power Supply Connect the supplied AC power cord into the AC IN socket of the projector. The STANDBY indicator lights up and the projector goes into the standby mode. Component cable (commercially available) COMPONENT VIDEO OUT Note : Make sure the AC power cord is firmly connected into the AC IN socket. Component cable (commercially available) COMPONENT VIDEO OUT STANDBY FL OFF DVD Player STANDBY FL OFF DVD Player S-video cable (commercially available) S-VIDEO OUT VIDEO OUT Video cable (commercially available) VCR 8 Connection with a HD-Video, DVD Player, Satellite, Cable Tuner or PC You can connect this projector to HD-Video /PC using RGB IN port, or DVD Plyer /Satellite /Cable Tuner /PC using HDMI IN port. Connect one end of the RGB cable to the RGB IN port, or one end of the HDMI cable to the HDMI IN port on the projector. Connect the other end to the corresponding port on a HD-Video, Satellite, Cable Tuner or personal computer. Advanced Connection You can control total home theater system using PC or Marantz receiver equipment. For installing below system, consult with Marantz authorized dealer. Screen Note : When projecting a video image from a device connected to the HDMI terminal, follow the procedure below. Set the input video source to HDMI input. Turn on power of the device connected to the HDMI terminal of the unit (i. e. If the procedure above is not followed, projected image may corrupt. For the details of the HDMI terminal on the device connected with the unit, see the instruction manual of the device. RS-232C cable (straight type, commercially available)   External Controller RGB (D-Sub monitor) cable (commercially available) RGB out RGB OUT or or DVI-D out DVI-D out or HDMI out 3. 5mm Mini Plug (Mono) (commercially available) HD-Video / Satellite / Cable Tuner / DVD Player Control Adapter cable (commercially available) REMOTE CONTROL IN REMOTE CONTROL OUT Monitor output RGB OUT RGB out or or DVI-D out DVI-D out Control Adapter cable (supplied) Receiver equipment HDMI-HDMI cable or HDMI-DVD-D cable (commercially available) IBM VGA or Compatible PC 9 ENGLISH INITIAL SETTING Turning on the Power 1. ( The ON indicator lights up. Detail Focusing You can strictly focus the image with focus pattern. Press the PATTERN button to project the focus pattern on the screen. ENGLISH 2.  P. 8) / I button on the projector. STANDBY PATTERN ON Press the ON button on the remote controller or the V-MUTE MENU ENTER STANDBY PATTERN ON V-MUTE MENU 2. Turn the Focus ring to make an adjustment. Adjust the focus for the sharpest image possible to obtain, using focus pattern. ENTER Zooming and Focusing Project an image on the screen roughly at first. Turn the Zoom ring and adjust to the desired size within the zoom range. WIDE: Enlarges (zooms in) the projected image. TELE: Reduces (zooms out) the projected image. [. . . ] ( Initialize the sensor by taking the correct procedures. (  P. 26) Set the lens shift knob to the correct (center) position by taking the correct procedures. ( P. 26)  Notes: If the lamp still does not function after the replacement and initialization of the lamp life, contact a Marantz authorized dealer, or service center. In such case, shut power OFF and unplug the power cable from AC power outlet. [. . . ]