User manual MARANTZ WB4001T

[. . . ] FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY. [. . . ] Make sure that none of these parts are missing before beginning installation. If there are parts missing stop the installation and contact Marantz. Wall plate (Qty 2) GriplatesTM (Qty 8) Mounting brackets (Qty 2) 5/16" x 3" Lag Bolts (wooden studs only) (Qty 8) M4 x 20mm Phillips Head Screws (Qty 8) 5/16" Flat Washers (Qty 8) M6 x 12 Safety knobs (Qty 2) Template (Qty 1) 1. 1 Installation Tools Soft Material/ Blanket Drill Gun 5/16" Socket Wrench Pencil Phillips Head Screw Driver Tape Measure Level (Supplied) -4- 2. 0 FINDING THE CENTER OF THE DISPLAY WARNING: PROPER INSTALLATION PROCEDURE BY QUALIFIED PERSONNEL AS OUTLINED IN THE INSTALLATION INSTRUCTIONS MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. WARNING: INVERT THE FLAT PANEL, PLACE IT ON A SOFT, FLAT SUFRACE TO PREVENT DAMAGE TO THE FLAT PANEL. FAILURE TO DO SO WILL RESULT IN DAMAGING THE FLAT PANEL. DO NOT LAY THE FLAT PANEL ON THE FLOOR WITHOUT ANY PROTECTION TO THE GLASS. AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. Step 1 Once the flat panel is inverted, use a measuring tape to find the center of your flat panel measuring from outside to outside of the chassis (Figure 1). Top of flat panel Step 2 Using a pencil lightly mark the center of your flat panel (Figure 2). Mark the center of the flat panel Inverted flat panel Measuring tape C L Bottom of flat panel Inverted flat panel C L Figure 2 Figure 1 -5- 3. 0 POSITIONING THE MOUNTING BRACKETS Step 4 Step 3 Lay the mounting brackets (stamped arrows Match the center of viewing guide with the center facing out) Figure 3. line you marked in Step 1 (Figure 4). Mounting brackets Bottom of flat panel Align the mounting brackets C L Arrows facing out Bottom of flat panel Figure 3 Figure 4 Step 5 The mounting brackets are designed with a center of viewing guide on the side of them (Figure 5). Mounting bracket Bottom of flat panel Center of viewing guide Figure 5 -6- 4. 0 SECURING THE MOUNTING BRACKETS Step 7 Once the mounting brackets are aligned, secure the GriplateTM to the flat panel. NOTE: The dimples of the top plates have to be facing up and the bottom dimples must be facing down. Use (1) GriplateTM per mounting point (Figure 7). Step 6 The GriplatesTM have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires. EXAMPLE: If your plasma uses M8 x 20 Phillip screws. Use the M8 mounting points (Figure 6). DIMPLES Phillips screw driver DIMPLES FACING UP DIMPLES FACING UP DIMPLES FACING DOWN M4 M5 M6 M8 DIMPLES FACING DOWN Bottom of flat panel Figure 6 Figure 7 -7- 5. 0 WOODEN STUD LOCATION Step 9 Align the center viewing port from the carton template to the center of the wood studs horizontally. Match the center of viewing port to the center of viewing height desired and mark a line on the bottom of the carton template (Figure 9). NOTE: This marking will reference the center of your flat panel display once mounted on the wall (Figure 9). Step 8 Using a (commercially available) wood stud finder, locate the 16" or 24" stud centers behind the wall. Once found, make a pencil marking on the center of the wood studs (Figure 8). [. . . ] CAUTION: Do not over tighten the M6 screws to the rods (Figure 16). Lateral shift Figure 16 - 11 - 10. 0 TECHNICAL SPECIFICATIONS Dimensions are in Inches and (mm) 28. 000 (171. 2) 16. 000 (406. 4) CL 1. 245 (31. 75) A B H 5. 000 (127) 19. 000 (482. 6) 12. 000 (304. 8) CL 10. 500 (266. 7) 21. 000 (533. 4) 5. 000 (127) C G 16. 000 (406. 4) 16. 000 (406. 4) D F 16. 000 (406. 4) 24. 290 (616. 97) E 2. 331 (59. 21) G A. 5/16" x 3" Lag screws and flat washers H. Safety knobs H 1 20. 500 (520. 7) 2 FINE TUNE TILT ADJUSTMENTS 1. [. . . ]