User manual MARANTZ WB6001T

[. . . ] FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY. [. . . ] If there are parts missing stop the installation and contact Marantz. Wall plate (Qty 2) GriplatesTM (Qty 6) Universal Mounting Brackets (Qty 2) 5/16" x 3" Lag Bolts (wooden studs only) (Qty 8) M8 x 20mm Phillips Head Screws (Qty 6) 5/16" Flat Washers (Qty 8) M6 x 12mm Safety Knobs (Qty 2) 1. 1 Installation Tools Soft Material/ Blanket Drill Gun 5/16" Socket Wrench Pencil Phillips Head Screw Driver Tape Measure Level (Supplied) -4- 2. 0 FINDING THE CENTER OF THE DISPLAY WARNING: Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury and possible damage to the flat panel. WARNING: DO NOT LAY THE FLAT PANEL ON THE FLOOR DURING ANY STEP OF THE INSTALLATION PROCESS. . AT LEAST TWO QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL Step 1 Use a measuring tape to find the center of your flat panel measuring from outside to outside of the flat panel (Figure 1). Step 2 Using a pencil lightly mark the center of your flat panel (Figure 2). Top of flat panel Mark the center of the flat panel Inverted flat panel Measuring tape C L Bottom of flat panel Inverted flat panel C L Figure 2 Figure 1 -5- 3. 0 POSITIONING THE MOUNTING BRACKETS Step 4 Step 3 Lay the mounting brackets (stamped arrows Match the center of viewing guide with the facing out) - (Figure 3). centerline you marked in Step 1 (Figure 4). Inverted Flat Panel Align the Mounting Brackets C L Bottom of Flat Panel Bottom of the Flat Arrows Facing Out Figure 3 Figure 4 Step 5 The mounting brackets are designed with a center viewing guide on the side of them (Figure 5). Mounting Brackets Bottom of Flat Panel Center of Viewing Guide Center of Flat Panel Figure 5 -6- 4. 0 SECURING THE MOUNTING BRACKETS Step 7 Once the mounting brackets are aligned, secure the GriplateTM to the flat panel. NOTE: The dimples of the top plates have to be facing up and the bottom dimples must be facing down. Use (1) GriplateTM per mounting point (Figure 7). Step 6 The GriplatesTM have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires. EXAMPLE: If your plasma uses M8 x 20 Phillip screws. Use the M8 mounting points (Figure 6). DIMPLES Phillips screw driver DIMPLES FACING UP DIMPLES FACING UP DIMPLES FACING DOWN M4 M5 M6 M8 DIMPLES FACING DOWN 3/4" Bottom of flat panel Figure 6 Figure 7 -7- 5. 0 WOODEN STUD LOCATION Step 9 Measure from the floor to the desired viewing height and mark the wall. NOTE: This marking will reference the center of your flat panel display once mounted on the wall (Figure 9). Step 8 Using a (commercially available) wood stud finder, locate the 16" or 24" stud centers behind the wall. Once found, make a pencil marking on the center of the wood studs (Figure 8). NOTE: The wall plates have (3) 16" and (1) 24" mounting slot positions. Wood Stud Finder (Commercially Available) Mark the Wall and the Center of the Studs 16" 16" Measure and mark the viewing height desired on the wall. Wooden Studs Figure 8 Figure 9 -8- Step 10 Place the bottom portion of the wall plate to the reference line and mark the four (4) lag bolt mounting points through the wall plate slots on the wall (Figure 10). Step 11 Level the wall plate with the reference arrow pointing up to the ceiling (Figure 11). Mounting Surfaces Wood studs: Drill four (4) ¼" pilot holes to the marked wall. Concrete wall: Drill four (4) 3/8" pilot holes to the marked wall. Drill Gun Pilot Holes 16" 16" Wall Plate Mounting Slots Level Wooden Studs Figure 10 Figure 11 -9- Step 12 ­ Wooden Stud Installation Level and secure the lower plate to the wall with the reference arrow facing up to the ceiling. Secure the plate using the four (4) 5/16" lag bolts and flat washers (supplied) ­ (Figure 12). Repeat Step 5 to secure the upper wall plate to the wall (Figure 12). CAUTION: NOTE: Do not over tighten the lag bolts. [. . . ] CAUTION: Do not over tighten the ¼"-20 screws to the rods (Figure 16). Lateral shift Figure 16 - 12 - 8. 0 TECHNICAL SPECIFICATIONS 28. 000 (171. 2) 16. 000 (406. 4) CL Dimensions are in Inches and (mm) 1. 245 (31. 75) A B H 5. 000 (127) 19. 000 (482. 6) 12. 000 (304. 8) CL 10. 500 (266. 7) 21. 000 (533. 4) 5. 000 (127) C G 16. 000 (406. 4) 16. 000 (406. 4) D F 16. 000 (406. 4) 24. 290 (616. 97) E 2. 331 (59. 21) G H A. 5/16" x 3" Lag screws and flat washers H. Safety knobs 20. 500 (520. 7) 1 2 1. [. . . ]