User manual MARANTZ WIZZ IT 3

[. . . ] • Editing of RC3001 setting data • Backup of RC3001 setting data to a PC Support OS • Windows 2000 • Windows XP • Windows Vista Minimum requirements for PC • 500 MHz Intel Pentium III workstation or equivalent • 128MB of RAM • 250MB free Hardisk space • Free USB port Recommended requirements for PC • 1. 2 GHz Intel Pentium IV workstation or equivalent • 512MB of RAM • 500MB of free Hardisk space • Free USB port CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 CONNECT PC AND REMOTE CONTROLLER . . . . . . . . . . . . 2 WIZZ. IT 3 OPERATION . . . . . . . . . . . . . . . . . . . . . . . 3 ICON DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 EDITING A NEW CONFIGURATION FILE . . . . . . . . . . . . . . . . . . . . 4 ACTION WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 LABEL WINDOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 LEFT SIDE SOFT BUTTON SETTING . . . . . . . . . . . . . . . . . . . . . . . . 13 RF SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 REGISTERING TO MY DATABASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 OTHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 1 RC3001_E_Wizzit3_ENG. indd 1 07. 9. 3 1:38:28 PM INSTALLING Wizz. it 3 1. 2. At first, you download the software Wizz. it 3 from the Home Entertainment section of your region in Marantz Website http://www. marantz. com. [. . . ] The devices are registered automatically starting from Device 1 on the Home page for the number of devices that were set. Double-click the HOME icon, and then select and double-click Page1. The remote controller illustration screen appears on the screen. Double-click the button on the right of each device name to display the Key Property screen. Select Label, and then assign names to the devices. The names can be up to 9 characters in length. (Refer to page 12. ) Select Action to select the action that is performed. The jump operation is automatically set to each device by default. (Refer to page 5. ) To make the settings for each device, select the device under the tree display, and then double-click the page of the device to display the remote controller illustration screen. Double-click each button to display the Property screen. (Refer to page 5. ) To add more pages, click the Add New Page icon. After the settings are completed, connect the remote controller to the PC using a USB cable. Click the Download icon to write the settings in the user file to the remote controller. 3. 7. 8. Note: Do not disconnect the USB cable while downloading. This could cause data to be erased in the remote controller so that it no longer functions properly. 9. It is recommended that you click the Save icon to save to the PC the user file that was set. Effectively combining Jump/Link operations enables building of a user interface in the remote controller that is optimized for the customer s operating conditions. 4 RC3001_E_Wizzit3_ENG. indd 4 07. 9. 3 1:38:30 PM ACTION WINDOW w e q r t y u i o q Action List This list sets the One Touch Operation (Macro). w Add IR Code This is used when setting the IR command to be sent. (Refer to page 6, Add IR Code Window . ) e Create Link This sets the links for the Action List. (Refer to page 10, Create Link Window . ) r Add Delay This sets a delay time between commands in the action list if necessary. The adjustment range is 0. 1 to 32 seconds in 0. 1 sec/step. t Create Jump This sets which page is jumped to in the middle or end of the action list. [. . . ] After making the settings, click OK. 11 RC3001_E_Wizzit3_ENG. indd 11 07. 9. 3 1:38:31 PM LABEL WINDOW t q w e r Key Area This is used to set the command name displayed on the remote controller LCD. q Name This allows setting of a name of up to 9 alphanumeric characters, symbols, or icons in length. To select, click the input characters in the key area. w A This is used to enter uppercase letters. [. . . ]