User manual MARMITEK IP EYE ANYWHERE 341 ADVANCED INSTALLATION GUIDE

[. . . ] IP EYEANYWHER ANYWHERETM EYE IP EYE ANYWHERE 241/341 Advanced Installation Guide 20377 / 20110202 · IP EYE ANYWHERE 241/341TM ALL RIGHTS RESERVED MARMITEK © Preface Thank you for purchasing the Marmitek H. 264/MPEG4/MJPEG Day&Night or True Colour Megapixel Network Camera, a standalone system that can be connected directly to an Ethernet or Fast Ethernet network. Equipped with a megapixel CMOS sensor, the camera allows you to capture a wider field of view with a resolution of up to 1280 x 1024. With support for latest H. 264 technology, you can record streaming video that utilizes high quality H. 264 images to your hard drive, enable motion detection and setup automated e-mail alerts for security. With the Infrared LEDs and light sensor on the camera (IPEA 241 only), you can capture clear images even in the dark environment. [. . . ] Once the required settings have been completed, your wireless network can be protected by simply pressing the WPS button on the camera. z z PROTECTED SETUP: Press the Reset to Unconfigured button to reset the WPS configuration of the camera. WPS - PIN Mode: The PIN (Personal Information Number) mode builds the connection by entering the PIN Code directly. Once you enter the PIN Code of the camera on the router (or access point) that supports WPS, you can directly build a WPS connection between the camera and the device by simply pressing its WPS button. - PBC Mode: The PBC (Push Button Configuration) mode builds the connection by scanning the devices in the wireless network. Once you press the camera's WPS button, it starts to scan the WPS devices in the wireless network, and then you can build the WPS connection by clicking the Connect button. z TIP Device Status: Display the WPS configuration of the camera. The Power LED indicates the WPS connection status by: - blinking 3 times when the connection is built successfully. - repeating 3 times of short-short-long blink when the connection is failed. 40 © MARMITEK 4. 5 Setting up Video & Audio The Video & Audio menu contains four sub-menus that provide the video and audio settings for the camera. 4. 5. 1 Video & Audio >> Camera z Image Setting - Brightness: Adjust the brightness level from 0 ~ 100. - Saturation: Adjust the colours level from 0 ~ 100. - Sharpness: Adjust the sharpness level from 0 ~ 100. TIP Click Default then Apply to restore the default settings of the three options above. - Mirror: Select Vertical to mirror the image vertically, or select Horizontal to mirror the image horizontally. IPEyeAnywhere 241 / 341TM 41 - Light Frequency: Select the proper frequency according to the camera's location to reduce the flicker: 50Hz, 60Hz or Outdoor. TIP When the camera is installed indoors, the Light Frequency option can be set normally (50Hz or 60Hz). However, the image of live video might be over exposure if the camera is focusing on the object outdoors. When this happens, you can set the option as Outdoor (even when the camera is installed indoors) to fix over exposure issue. 4. 5. 2 Video & Audio >> Video z H. 264 - Video Resolution: Select the desired video resolution from the four formats: SXGA, VGA, QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. - Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. - Frame Rate: Select a proper setting depending on your network status. MPEG4 - Video Resolution: Select the desired video resolution from the three formats: VGA, QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. - Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. - Frame Rate: Select a proper setting depending on your network status. MJPEG - Video Resolution: Select the desired video resolution from the four formats: SXGA, VGA, QVGA and QQVGA. © MARMITEK z z 42 The higher setting (VGA) obtains better video quality while it uses more resource within your network. - Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. - Frame Rate: Select a proper setting depending on your network status. NOTE The camera supports H. 264, MPEG4 and MJPEG compression. [. . . ] RTP (Real-time Transport Protocol) is a data transfer protocol defined to deliver live media to the clients at the same time, which defines the transmission of video and audio files in real time for Internet applications. RTSP (Real-time Streaming Protocol) is the standard used to transmit stored media to the client(s) at the same time, which provides client controls for random access to the content stream. RTSP S Server SIP It is a simple computer that provides resources, such as files or other information. SIP (Session Initiated Protocol) is a standard protocol that delivers the real-time communication for Voice over IP (VoIP), which establishes sessions for features such as audio and video conferencing. © MARMITEK 70 SMTP SNMP Station Subnet mask The Simple Mail Transfer Protocol is used for Internet mail. [. . . ]