User manual MARMITEK IP EYE ANYWHERE 470 ADVANCED INSTALLATION GUIDE

[. . . ] P Eye Anywhere 470 CAMERA IP SERIES Low Lux MPEG4/MJPEG Dome Network Camera 3 ADVANCED INSTALLATION GUIDE 20310 / 20091117 · IP Eye Anywhere 470TM ALL RIGHTS RESERVED MARMITEK © PREFACE Thank you for purchasing the IPEyeAnywhere470, a standalone system that can be connected directly to an Ethernet or Fast Ethernet network. The camera features the latest Motion JPEG and MPEG-4 image technology, advanced management functionality, and GPIO connectors (e. g. connecting to the door sensors or alarm bells), allowing you to record streaming video (Motion JPEG or MPEG-4 ), enable motion detection, and setup automated FTP/Email/ Network Storage service for security. The audio function (connected external microphone and audio-out device like the active speaker) of the camera allows you to deliver/receive sound to/from the camera. [. . . ] z Ports Number - HTTP Port: The default HTTP port is 80. - RTSP Port: Configure the transmission of streaming data within the network. The default RTSP (Real Time Streaming Protocol) port is 554. NOTE If the camera is behind an NAT router of firewall, the suggested to be used is from 1024 to 65535. Network >> IP Filter The IP Filter setting allows the administrator to limit the users within a certain range of IP addresses to use the camera. To disable this feature, select the Disable option; otherwise, select the Accept option to assign the range of IP addresses that are allowed to access the camera, or select the Deny option to assign the range of IP addresses that are blocked to access the camera. z Accept - Start/End IP Address: Assign a range of IP addresses that are allowed to access the camera by entering the Start IP address and End IP address options. When you are finished, click Add to save the range setting. You can repeat the action to assign multiple ranges for the camera. 30 © MARMITEK For example, when you enter 192. 168. 0. 50 in Start IP Address and 192. 168. 0. 80 in End IP Address, the user whose IP address located within 192. 168. 0. 50 ~ 192. 168. 0. 80 will not be allowed to access the camera. - Accept IP List: The list displays the range setting(s) of IP addresses that are allowed to access the camera. To clear the setting, select a range of IP addresses from the list and click Delete. z Deny - Start/End IP Address: Assign a range of IP addresses that are blocked to access the camera by entering the Start IP address and End IP address options. When you are finished, click Add to save the range setting. You can repeat the action to assign multiple ranges for the camera. For example, when you enter 192. 168. 0. 50 in Start IP Address and 192. 168. 0. 80 in End IP Address, the user whose IP address located within 192. 168. 0. 50 ~ 192. 168. 0. 80 will not be allowed to access the camera. - Deny IP List: The list displays the range setting(s) of IP addresses that are blocked to access the camera. To clear the setting, select a range of IP addresses from the list and click Delete. IPEyeAnywhere 470 TM 31 4. 5 Setting up Video & Audio The Video & Audio menu contains four sub-menus that provide the video and audio settings for the camera. Video & Audio >> Camera z Image Setting - Brightness: Adjust the brightness level from 0 ~ 100. - Saturation: Adjust the colors level from 0 ~ 100. - Sharpness: Adjust the sharpness level from 0 ~ 100. Click Default to restore the default settings of the three options above. - Mirror: Select Vertical to mirror the image vertically, or select Horizontal to mirror the image horizontally. 32 © MARMITEK Video & Audio >> Video z MPEG4 - Video Resolution: Select the desired video resolution from the three formats: VGA, QVGA, and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. - Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. [. . . ] RTP (Real-time Transport Protocol) is a data transfer protocol defined to deliver live media to the clients at the same time, which defines the transmission of video and audio files in real time for Internet applications. RTSP (Real-time Streaming Protocol) is the standard used to transmit stored media to the client(s) at the same time, which provides client controls for random access to the content stream. S Server SIP It is a simple computer that provides resources, such as files or other information. SIP (Session Initiated Protocol) is a standard protocol that delivers the real-time communication for Voice over IP (VoIP), which establishes sessions for features such as audio and video conferencing. The Simple Mail Transfer Protocol is used for Internet mail. [. . . ]