User manual MARSHALL JVM205H HEAD

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MARSHALL JVM205H HEAD. We hope that this MARSHALL JVM205H HEAD user guide will be useful to you.

Lastmanuals help download the user guide MARSHALL JVM205H HEAD.


Mode d'emploi MARSHALL JVM205H HEAD
Download
Manual abstract: user guide MARSHALL JVM205H HEAD

Detailed instructions for use are in the User's Guide.

[. . . ] ENGLISH From Jim Marshall I would like to thank you personally for selecting one of our new `JVM' amplifiers. Since I started Marshall Amplification in 1962 I have witnessed some incredible breakthroughs and advances in amplifier design technology, such as master volume amps, channel switching, reverb, effects loops, MIDI technology, speaker emulation and digital effects processing, to name just a few. These may all seem commonplace features nowadays but that certainly wasn't always the case. However, the same values that were present in the first Marshalls are still very much here today: meticulous workmanship, reliability, stylish looks and, above all, great Marshall tone. [. . . ] ENGLISH When pressing in the same channel it cycles the modes: GREEN > ORANGE > RED > GREEN. . . Each mode remembers the FX, Reverb and Master settings. Example: You are in OVERDRIVE ORANGE with FX + REVERB and you press CLEAN. The amp switches to the last Clean mode you had (let's assume it was CLEAN GREEN with REVERB). If you press the OVERDRIVE switch you go back to OVERDRIVE ORANGE with FX + REVERB. This allows bouncing between channels without losing the settings. If you now press OVERDRIVE again, you go to OVERDRIVE RED with whatever FX, MASTER and REVERB settings you had last time you were in this mode. Pressing REVERB (7) switches the reverb ON and OFF in the current channel. Pressing FX LOOP (4) switches the parallel FX loop ON and OFF in the current channel. Connection to the amplifier requires a standard mono 1/4" jack to jack cable. Any guitar lead will work and practically there should be no limit in its length. When the front panel FOOTSWITCH / MIDI PROGRAM switch is off, the footswitch operates in safe mode and executes the commands the moment the switch is pressed down. If you enter the FOOTSWITCH PROGRAM mode (LED red) you will be able to program the footswitch but nevertheless the footswitch and the amplifier will remain fully operational with the only difference that the commands will be executed when releasing the footswitches, as opposed to the normal mode. Each of the individual footswitches has 2 modes of operation: preset store and switch store. In preset store mode, any of the footswitches can be configured to store the current amplifier status. The current channel, master, FX and reverb status will be stored and recalled when the respective footswitch is pressed. To store the current status simply: Set the amplifier to FOOTSWITCH PROGRAM mode (red light ON). Press and hold the desired switch for about 3 seconds. The FX footswitch LED will flicker a couple of times indicating that the preset has been stored. In switch store mode, any of the footswitches can be configured to replicate the front panel switches and the amplifier will react exactly in the same way as when you operate them on the front panel. All the front panel switches can be mapped to any of the footswitches without any limitation. The only exception is the FOOTSWITCH / MIDI PROGRAM switch which cannot be assigned to the footswitch. To assign any of the front panel switches (except FOOTSWITCH / MIDI PROGRAM) to any of the footswitches simply: Set the amplifier to FOOTSWITCH PROGRAM mode (red light ON). [. . . ] Turn the MIX control to WET and switch the FX loop on. Store this preset as described before and label it for example as `tuner'. Obviously in this configuration it is not possible to connect any other effect to the loop. Hint 3: To use a different preamplifier and combine it with the JVM channels, connect the external preamplifier output to the parallel loop return and turn the MIX to WET. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MARSHALL JVM205H HEAD

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MARSHALL JVM205H HEAD will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag