User manual MARSHALL MEGASTACK MG15FXMSDM

[. . . ] Details of the individual control and voice settings can be found on page 40. power Manual In manual mode the amp's settings always match the physical positions of the controls. Changing channel only changes the channel, NO presets are recalled, NO other controls are altered. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Factory presets Clean Absolution Symphony Chorus New Wave of British Heavy Metal Holy Solo 1. Input Jack Socket Jack input for your guitar. one that's screened/shielded) to help prevent noise, interference and unwanted feedback. [. . . ] FX The FX control is split into four segments and selects the type of FX and adjusts its associated settings. When the FX control is set to `0' the FX are switched off, the status of the FX is also indicated on the optional footcontroller. 0 Chorus Phaser Delay Flanger FX Off Speed increases and depth is reduced as knob is turned clockwise. Speed increases as knob is turned clockwise. Speed increases, feedback and depth are reduced as knob is turned clockwise. Delay level is increased as knob turned clockwise. ENGLISH When moving from an OD channel to a Clean/Crunch channel, the unit remembers the last channel you were in before leaving. If you have moved from the Crunch Channel to an OD channel and you press the Clean/Crunch switch (3), the amplifier will revert back to the Crunch channel - rather than starting again in the Clean channel. Modes The amplifier operates in two modes - Preset and Manual. To change between these two modes, you must hold the Tap switch (10) down for at least two seconds. When in manual mode the Store switch (12) lights red and the selected channel light (3 or 5) will start to flash. The amplifier will remember the last mode it was in after power off and revert to it the next time it is powered on. Preset This is the factory default operation of the amplifier. Note: The specific mains input voltage rating that your amplifier has been built for is shown on the back panel. Before connecting to the mains electricity supply, always ensure that your amplifier is compatible with your electricity supply. If you have any doubt, please get advice from a qualified technician. Your Marshall dealer will help you in this respect. Please ensure the amplifier is switched off and unplugged from the mains electricity supply before being moved. In Preset mode the position of all controls except Master Volume (13) are stored within each channel. Each channel should be considered a preset. Selecting a channel automatically recalls the settings stored within the channel. Note: The physical position of the front panel controls, except Master Volume (13) which is not storable, will now not match the actual settings of the amplifier. All front panel switches will automatically update. Tap Tempo The Tap Tempo switch (10) is used for the Delay effect only. The Tap Tempo switch matches the delay time to the time between two presses. The Tap Tempo LED flashes red at the selected/recalled delay time. Altering a control will cause the associated parameter to jump to the current physical position of that control. When a control is altered the selected channel light (3 or 5) will start to flash indicating that the current preset has been altered. To store the updated settings, push the Store switch (12). If you select another channel without pressing Store (12) then any altered settings will be lost as the new channel and its settings are recalled. The number of repeats is reduced as the delay time decreases. If you change from a channel with delay to one without delay the effect will spill between channels. [. . . ] * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. * EUROPE ONLY - Note: This equipment has been tested and found to comply with the requirements of the EMC Directive (Environments E1, E2 and E3 EN 55103-1/2) and the Low Voltage Directive in the E. U. The indicator dot on the lower right hand corner shows if the current closest note is #. When either a Channel preset or Footswitch preset has been altered the Digital Display (3) will begin to flash. The footswitch will flash the relevant number if a Footswitch preset has been altered or will flash a "-" if a Channel preset has been altered. The LED Status Panel (2) is used to show how far away from the closest note the current note being played is. [. . . ]