User manual MARTIN MAC 600

[. . . ] MAC 600/E user manual © 1997 - 2002 Martin Professional A/S, Denmark. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin Professional A/S, Denmark. H section 1 INTRODUCTION About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Display goes out 2 minutes after last key press. Disable DMX lamp off command. * Enable DMX reset command. Disable DMX reset command. * Lamp strikes automatically within 90 seconds of power on. Effect wheels turn the shortest direction. * Effect wheels always turn same direction. * Shutter "helps" dimmer black out. Shutter not affected by dimmer commands. Optimize effects for speed. * Optimize effects for silence. * Enable pan/tilt position correction system. Select Schiederwerk ballast (MAC 600 E's after S/N 4020700000) Select Mitronic ballast (MAC 600 E's with date-based S/N or before S/N 4020700000) * Setting may be overridden via DMX. See the protocol for details. Display on/off Display intensity DMX lamp off SPEC/dISP OFF SPEC/dINT SPEC/dLOF 10-100 ON OFF ON DMX reset SPEC/dRES OFF ON Automatic lamp on Automatic protocol detection Shortcuts SPEC/ALON OFF ON SPEC/AUTO OFF ON SPEC/SCUT OFF ON Automatic shutter SPEC/ASHT OFF NORM Studio mode MOdE STUd ON Pan/tilt feedback SPEC/FEbA OFF ON Effects feedback SPEC/EFFb OFF REG Fan speed SPEC/FAN FULL Electronic ballast type SCHI SPEC/ETYP MITR 12 MAC 600/E Readouts U s a g e r e a d o u t s ( TIME) Read the total number of power-on hours (Po H), power-on hours since last reset (RPoH), total lamp hours (LA H), lamp hours since last reset (RLAH), total number of lamp strikes (LSTR), and the number of lamp strikes since last reset (RLST). The resettable counters may be used to track overall usage and lamp life. To reset to zero, display the readout and then press [] for 5 seconds. D M X v a l u e r e a d o u t s ( dMXL) Read the DMX start code (STCO) and DMX values received for each channel. This is an easy way to check that the start code is 0 and that the fixture is receiving the expected commands. If the fixture is set to a DMX mode where some or all of the channels between 10 and 13 are not used, the readout on these channels will be N/A. Note: the channel number is 1 less in the readout than it is in the DMX protocol. S o f t w a r e v e r s i o n r e a d o u t s ( VER) Read the version number of the CPU software (CPU), pan/tilt feedback circuit (FEbA), and display module software (dISP). The CPU software version is also displayed for a moment at power up. T e m p e r a t u r e r e a d o u t s ( SPEC/ TEMP) Read temperature in the base (bASE) and head (HEAd) in Celsius. Temperatures below 25° C are shown as -25; temperatures above 100° C are shown as +100. The temperature sensors are calibrated at the factory and adjustment should not be necessary. The following procedure calibrates the sensors if they give no or faulty readings. Allow the unit to cool to room temperature (powered off for at least 4 hours). Measure the room temperature in Celsius. (To convert F° to C°, subtract 32° and then multiply by 0. 555. ) Power up the unit and allow it to reset. Press the [MENU] and [] keys at the same time and hold them for 3 seconds until "25" shows in the display. Press the [] and [] keys until the display shows the temperature measured. [. . . ] 0. 85 Electrical, electronic ballast version · · · Transformer taps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100/110/120/200/210/220/230/240 @ 50 - 60 Hz Power and current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690 W, 3. 2 A @ 230 V / 50 Hz Power factor (PF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 94 Fuses · · · · · Primary fuse, MAC 600, MAC 600 E @ 200 - 250 V AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]