User manual MARZOCCHI 2005 TAIWAN

[. . . ] USE OF THE MANUAL 8 · Carefully read, understand and follow the instructions given in this manual. This manual is an essential part of the product, and you should keep it in a safe place for future reference. 1 · If the use and maintenance instructions provided in this manual are not properly performed, or if the other instructions in this manual are not followed, an accident could occur, resulting in an accident, serious injury or death. · This manual does not explain how to assemble/disassemble the fork from the bicycle, the wheel, the steering set or any other component directly or indirectly associated with the fork that are not actually a part of the fork. · Please be advised that suspension system installation and repair requires specialized knowledge, tools and experience. [. . . ] Carefully follow the direction provided by the quick release manufacturer to properly tighten the quick release system. Failure to do so could cause the wheel to fall off, resulting in an accident, personal injury or death. · Tighten the cap positioned on the axle side using a 6 mm Allen key to the required tightening torque (see table 6. 17 Tightening torques). · Confirm that the supporting bushings (N) are still centered in the fork wheel axle clamp seat. · Check the correct fork-wheel alignment, by fully compressing the fork a few times. The wheel should not make contact with or come close to any portion of the fork. Check the owners manual for the brake system for the proper specifications. · Lift the front of the bicycle and spin the wheel a few times to verify the correct alignment with the disk brake. The wheel should not make contact with or come close to any portion of 6 mm E F English N H MZ025005 G L 3 89 6 mm E M H MZ025006 G F Picture 5 - Wheel installation on a QR20 "with bolt" fork MZ025 Installation 3. 3. 3 Wheel installation on D-Street 24" forks Picture 6 For correct fork function, please follow the instructions here below when installing the wheel: · Insert the axle (1) through the right fork wheel axle clamp, the wheel and the left fork wheel axle clamp. · Tighten the axle acting on the cap (2), using a 6 mm Allen key to the required tightening torque (see table 6. 17 - Tightening torques). · Check the correct fork-wheel alignment, by fully compressing the fork a few times. The wheel should not make contact with or come close to any portion of the fork. Lift the front of the bicycle and spin the wheel a few times to verify the correct alignment with the disk brake. Check the owners manual for the brake system for the proper specifications. · Tighten the screws (3) positioned on both wheel axle clamps, using a 5 mm Allen key to the required torque (see table 6. 17 Tightening torques). English 1 6 mm 3 90 2 MZ025006 5 mm 3 Picture 6 - D-Street 24" wheel installation MZ025 Installation 3. 4 Fender Installing Picture 7 8 mm A fender may be installed on the ø 32 mm legs forks. The fender can be provided with the fork or purchased separately. When assembling the fender (P) you must insert the small support bushing (Q) between the screw and the fender as shown in the picture, and tighten the screws (R) with a 8 mm Allen wrench to the required torque (see table 6. 17 Tightening torques). P Q MZ025010 R English Picture 7 - Fender Instatting 3. 5 Handlebar clamp installing Picture 8 3 91 The Drop-Off Triple model can be provided with handlebar clamp (the handlebar clamp may be sold together with the fork or purchased separately); for the installation please carefully follow these instructions: Install the handlebar lower mounting (S) on the upper crown, in a way that the holes coincide. Fix the handlebar clamp by tightening the screws (T) to the required torque (see table 6. 17 - Tightening torques). Install the handlebar in the mounting in a central position. Lock the handlebar with the appropriate clamp (U). Tighten the screws (V) to the required torque (see table 6. 17 - Tightening torques). [. . . ] Any disputes arising out of this agreement or the use of this Marzocchi Suspension System will be governed by the laws of the country of Italy and will be decided by the Courts of Bologna, Italy. English MARZOCCHI and BOMBER licensed by Marzocchi S. p. A. trademarks 7 113 MZ025 MARZOCCHI distributors and service centers MZ025 211 Marzocchi distributors and service centers MARZOCCHI DISTRIBUTORS AND SERVICE CENTERS EUROPE COUNTRY AUSTRIA COMPANY TRENDSPORT GmbH Südtirolerstr. , 1 - A6911 LOCHAU ­ Austria Contact: Mr. Klaus Froeis Tel. : +43 (0)5574 47147 · Fax: +43 (0)5574 52334 Info@trendsport. co. at RAKBIKE S. A. Avenue Jeanne 13 ­ 1050 IXELLES - Belgium Contact: Rafi Kasparian Tel. [. . . ]