User manual MASTERCRAFT PROSTAR 205 VRS 2001

[. . . ] WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75. EN-2 Contents Important safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preparing your projector. [. . . ] The menu settings are reset to the factory defaults (except the LANGUAGE, PASSWORD FUNCTION, IMAGE CAPTURE, and NETWORK settings). SCART INPUT ON / OFF LAMP WARNING STANDARD SHORT TERM HIDE OSD OFF ON OK RESET ALL • CINEMA MODE can be adjusted only when a TV60, TV50, 480i, 576i or 1080i signal is being displayed. • When SCART INPUT is set to ON, normal computer signals aren’t projected. • Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped with the SCART terminal. • Some AV devices equipped with the SCART terminal aren’t compatible with this projector. • The RESET ALL process may take some time to complete. EN-35 Menu operation (continued) SIGNAL menu opt. opt. SIGNAL A U H V SIGNAL AUTO 1024 x 768 0 0 0 0 AUTO 100% ON ENTER SIGNAL USER 60. 00 Hz 48. 36 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. TRACKING RESOLUTION (MEMORIZE) VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES EXECUTE CANCEL CLAMP POSITION CLAMP WIDTH VERT. LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) 1 1 AUTO OFF 0 0 0 0 R RG GB B COMPUTER INPUT OVER SCAN HOLD USER ITEM MEMORY CALL SETTING AUTO / MEMORY 1 MEMORY 2 ) 640-1920 / RESOLUTION (MEMORIZE VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES 350-1200 EXECUTE CANCEL OK OK 0-999 0-999 0-31 0-9999 AUTO RGB YCBCR/YPBPR HORIZ. TRACKING COMPUTER INPUT OVER SCAN HOLD USER CLAMP POSITION CLAMP WIDTH VERT. Select this option when connecting the projector to high definition video equipment having R, G, and B output terminals. Select this option when connecting the projector to a DVD player or other device having Y, CB, and CR (or Y, PB, and PR) component video output terminals. Use to adjust the display area of projected image. Use to adjust the image when flagging occurs near the top of the screen. The USER menu is displayed for the following adjustments. Use to correct solid white or solid black in the projected image. Use to correct solid black in the projected image. Use to adjust the image when its motion doesn’t run smoothly. Use to select whether or not to enable the LPF. (See page 43. ) Use to adjust the image when noise appears on the top part of the image. Use to adjust the image when noise appears on the bottom part of the image. [. . . ] When it is set to STANDARD, this duration will be shorted. *2: Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be shorted up to 3000 hours. *3: When you press the POWER button on the projector or the remote controller, the STATUS indicator blinks red three times and then resumes red illumination. [. . . ]