User manual MAXENT MX-50X2

[. . . ] PDP Flat Panel 50" PDP Monitor Owners Manual Important Safety Instructions WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove the front or back covers. Refer servicing to qualified service personnel only. The lightning flash with arrow-head within a triangle is intended to inform the user that parts inside the product are a risk of electric shock. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are explained. Special Notices !! Certain programs may be copyrighted and any unauthorized recording in whole or in part may be in violation of copyright laws in the U. S. [. . . ] Connect the blue-colored (labed as PB or CB) jack from the DVD to the blue-colored PB/CB jack of the monitor. Connect the red (R) and white (L) audio jacks from the DVD to the R and L audio-in jacks located next to the PR/CR connector. 15 Display Connections Connecting a DVD (con't) Using S-Video Input Connect the S-Video (4-pin DIN) connector from the DVD to the S-Video input on the back of monitor. Connect the red (R) and white (L) audio jacks from the DVD to the (R) and (L) audio-in jacks located next to the S-Video connector. Note: !There are two sets of S-Video inputs provided. Using Composite Input Connect the yellow (video) out connector from the DVD to the yellow video input on the back of monitor. Connect the red (R) and white (L) audio-out jacks from the DVD to the R and L audio-in jacks located next to the yellow Video connector. Note: !There are two sets of composite inputs provided. 16 Display Connections Connecting a Set-Top Box Using Component Video Input There are two sets of component video inputs provided. You can use either set of component inputs to connect your STB. Some HDTV Set top boxes may not have a Component Video output. Connect the green-colored (labeled as Y) jack from the STB to the green-colored jack of the monitor. Connect the red-colored (labed as PR/CR) jack from the STB to the red-colored PR/CR jack of the monitor. Connect the blue-colored (labed as PB /CB) jack from the STB to the blue-colored PB/CB jack of the monitor. Connect the red (R) and white (L) audio jacks from the STB to the R and L audio-in jacks located next to the PR/CR connector. Using RGB Input Connect the 15-pin D-Sub RGB connector from the back of the HDTV set top box to the RGBIN Connector located on the back of the monitor. Connect the red (R) and white (L) audio-out jacks from the HDTV set top box to the R and L audio-in jacks located next to the RGB connector. Notes: !Some HDTV Set top boxes may not have a RGB output. Use Component Video input or DVI input method if this is the case. Upon connecting your HDTV set top box to the RGB input of the monitor, it may be necessary to adjust various picture settings on the monitor to correctly match the output of the HDTV set top box. This is caused by the different video timings set by various HDTV set top box manufacturers. (See Page 40 for more information). 17 Display Connections Connecting a Set-Top Box (con't) Using DVI Input Connect the DVI-D connector from the back of the HDTV set top box to the DVI-IN Connector located on the back of the monitor. Connect the red (R) and white (L) audio-out jacks from the HDTV set top box to the R and L audio-in jacks located next to the DVI-D connector. Notes: !Some HDTV Set top boxes may not have a DVI output. Use Component Video input or RGB input method if this is the case. Upon connecting your HDTV set top box to the DVI input of the monitor, it may be necessary to adjust various picture settings on the monitor to correctly match the output of the HDTV set top box. This is caused by the different video timings set by various HDTV set top box manufacturers. [. . . ] CLOCK PHASE Use clock phase to fine-tune the monitor to perfectly synchronize to the video signal source under RGB mode. H-Position, H-Size, V-Position and V-Size adjustments are only available in RGB, DVI, and Component input modes. 35 Picture Controls Picture-in-Picture Turning On PIP PIP and POP modes allow users to view two video input sources simultaneously. Press the key once on the remote control to engage in Picture-in-Picture mode. Pressing the key repeatedly will cycle thru the following modes: PIP Key When engaged in PIP mode, a small window is displayed in one of the four corners. [. . . ]