User manual MAXTOR C2EIES3050

[. . . ] MATROX CORONA-II CAMERA INTERFACE APPLICATION NOTE SONY XC-EI30/50, ES30/50 OCTOBER 15, 2001 Basics about the camera Camera Descriptions § § § § § § 754 × 484 @ up to 60 fps. 15. 734 MHz pixel clock rate. Mode of operations as per Matrox Imaging (in parentheses as per camera manufacturer) Basics about the interface modes Interface Modes § Continuous § Asynchronous reset (Restart/Reset mode) Camera Interface Briefs Mode 1: Continuous § § § § § 754 × 484 × 8-bit @ 30 fps. [. . . ] Refer to the camera manual for more information. § Camera Switch settings: Internal/External synchronization switch and DIP switches are set as follows, refer to the camera manual for additional information: EXT Internal/External Sync ON * * * * INT ü OFF * * * * Shutter Speed 1 Shutter Speed 2 Shutter Speed 3 Shutter Speed 4 Field/ Frame/ 5 Mode 6 Mode 7 Mode 8 ü ü ü ü * Shutter switches are not effective in this mode Mode 2: Asynchronous Reset (Restart/Reset mode) § Frame rate: The frame rate is determined by the frequency of the external trigger signal, up to a maximum of 30 fps. § Exposure time: The width (rising edge to falling edge) of the EXPOSURE1 (EXT. TRIG IN) signal plus a fixed internal camera delay of 1H to 2H equals the exposure time. The exposure time can be modified in the DCF using Matrox Intellicam or with the MIL digitizer control function MdigControl(). Refer to the appropriate manual or user guide for more information. COR2-CID-003 2 MATROX CORONA-II CAMERA INTERFACE APPLICATION NOTE SONY XC-EI30/50, ES30/50 OCTOBER 15, 2001 Specifics about the interface modes Camera Interface Details (continued) Mode 2: Asynchronous Reset (Restart/Reset mode) § Timing diagram: § Camera Switch settings: Internal/External synchronization switch and DIP switches are set as follows, refer to the camera manual for additional information: EXT Internal/External Sync ON * * * * INT ü OFF * * * * Shutter Speed 1 Shutter Speed 2 Shutter Speed 3 Shutter Speed 4 Field/ Frame/ 5 Mode 6 Mode 7 Mode 8 ü ü ü ü * Shutter switches are not effective in this mode Cabling details for this interface mode Cabling Requirements Mode 1: Continuous § Cable: DBHD44-TO-8BNC/O (open ended) cable required for video, synchronization and control signals. § Connection: Connections between the 12-pin connector of the camera and the 44-pin connectors of the Matrox Corona-II are as follows: CORONA2 (44-pin connector) Pin name VID1_IN GROUND Pin no. 15 17 -SONY XC-ST70/ST50/ST30 (12-pin connector) Pin name Pin no. VIDEO OUTPUT GROUND 04 03 COR2-CID-003 3 MATROX CORONA-II CAMERA INTERFACE APPLICATION NOTE SONY XC-EI30/50, ES30/50 OCTOBER 15, 2001 Cabling Requirements (continued) Mode 2: Asynchronous Reset (Restart/Reset mode) § Cable: DBHD44-TO-8BNC/O (open ended) cable required for video, synchronization and control signals. § External trigger: TTL external trigger signal connected to the OptoCoupled Trigger input (pin 34, 35) of the DBHD44-TO-8BNC/O cable. § Connection: Connections between the 12-pin connector of the camera and the 44-pin connectors of the Matrox Corona-II are as follows: CORONA2 (44-pin connector) Pin name VID1_IN EXPOSURE1 GROUND OPTOTRIG + OPTOTRIG Pin no. 15 38 17 35 34 - SONY XC-ST70/ST50/ST30 (12-pin connector) Pin name Pin no. [. . . ] Contact your local sales representative or Matrox Sales office or Matrox Imaging Applications at 514-822-6061 for assistance. Corporate headquarters: Canada and U. S. A. Dorval, Quebec H9P 2T4 Canada Tel: (514) 685-2630 Fax: (514) 822-6273 COR2-CID-003 [. . . ]