User manual MAXTOR CHEETAH 15K.5 SCSI

[. . . ] Users Guide Cheetah 15K. 5 SCSI ST3300655LW ST3300655LC ST3146855LW ST3146855LC ST373455LW ST373455LC ©2006, Seagate Technology LLC All rights reserved Publication number: 100384776, Rev. C October 2006 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, and SeaTDD are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. [. . . ] Operating--normal The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding 10­500 Hz @ 0. 5 G (zero to peak) Vibration may be applied in the X, Y, or Z axis. Operating normal translational random flat profile: 10­500 Hz b. Operating--abnormal Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding: 15 minutes of duration at major resonant frequency 10­500 Hz @ 0. 75 G (X, Y, or Z axis, zero to peak) Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. Operating abnormal translational random flat profile 10 - 500 Hz c. Non-operating The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives. The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding 5­22 Hz @ 0. 040 inches (1. 02 mm) displacement (zero to peak) 22­500 Hz @ 2. 00 G (zero to peak) Vibration may be applied in the X, Y, or Z axis. Non-operating translational random flat profile: 10­500 Hz 6. 4. 5 Air cleanliness 1. 2 gRMS 1. 2 gRMS 0. 4 gRMS The drive is designed to operate in a typical office environment with minimal environmental control. 6. 4. 6 Corrosive environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment. Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives. Cheetah 15K. 5 SCSI Product Manual, Rev. C 33 6. 4. 7 Acoustics Sound power during idle mode shall be 3. 6 bels typical when measured to ISO 7779 specification. Sound power while operating shall be 4. 3 bels typical when measured to ISO 7779 specification. There will not be any discrete tones more than 10 dB above the masking noise on typical drives when measured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive. 6. 4. 8 Electromagnetic susceptibility See Section 2. 1. 2. 6. 5 Mechanical specifications The following nominal dimensions are exclusive of the decorative front panel accessory. [. . . ] If your location is not listed here, dial our European CSO warranty center at +31-20-316-7222 from 8:30 A. M. (Central Europe time) Monday through Friday. The CSO warranty center is located in Amsterdam, The Netherlands. Seagate Service Centers Toll-free support numbers Call center Austria Belgium Denmark France Germany Ireland Italy Netherlands Norway Poland Spain Sweden Switzerland Turkey United Kingdom Presales and Technical Support -- 00 800-47324283 (00 800-4SEAGATE) 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-311 12 38 00 800-47324283 00 800-47324283 00 800-47324283 00 800-31 92 91 40 00 800-47324283 Warranty Service 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-311 12 38 00 800-47324289 00 800-47324289 00 800-47324289 00 800-31 92 91 40 00 800-47324289 FAX services--All Europe (toll call) Technical Support Warranty Service +1-405-324-3339 +31-20-653-3513 Africa/Middle East support services For presales and technical support in Africa and the Middle East, dial our presales and technical support call center at +1-405-324-4714 from 8:00 A. M. (Central Europe time) Monday through Friday. [. . . ]