User manual MAXTOR CHEETAH T10 SAS 2006

[. . . ] Cheetah T10 SAS ST3300555SS ST3146755SS ST373355SS ©2006, Seagate Technology LLC All rights reserved Publication number: 100433694, A October 2006 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, and SeaTDD are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications. [. . . ] The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not exceeding 60 Gs at a maximum duration of 2 msec (half sinewave). Shock may be applied in the X, Y, or Z axis. Operating--abnormal Equipment, as installed for normal operation, does not incur physical damage while subjected to intermittent shock not exceeding 40 Gs at a maximum duration of 11 msec (half sinewave). Shock occurring at abnormal levels may promote degraded operational performance during the abnormal shock period. Specified operational performance will continue when normal operating shock levels resume. Shock may be applied in the X, Y, or Z axis. Shock is not to be repeated more than two times per second. Non-operating The limits of non-operating shock shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives. The drive subjected to nonrepetitive shock not exceeding 75 Gs at a maximum duration of 11 msec (half sinewave) shall not exhibit device damage or performance degradation. Shock may be applied in the X, Y, or Z axis. The drive subjected to nonrepetitive shock not exceeding 250 Gs at a maximum duration of 2 msec (half sinewave) does not exhibit device damage or performance degradation. Shock may be applied in the X, Y, or Z axis. The drive subjected to nonrepetitve shock not exceeding 120 Gs at a maximum duration of 0. 5 msec (half sinewave) does not exhibit device damage or performance degradation. Shock may be applied in the X, Y, or Z axis. Cheetah T10 SAS Product Manual, Rev. Packaged Disc drives shipped as loose load (not palletized) general freight will be packaged to withstand drops from heights as defined in the table below. For additional details refer to Seagate specifications 30190-001 (under 100 lbs/45 kg) or 30191-001 (over 100 lbs/45 Kg). Package size Packaged/product weight Drop height <600 cu in (<9, 800 cu cm) 600-1800 cu in (9, 800-19, 700 cu cm) >1800 cu in (>19, 700 cu cm) >600 cu in (>9, 800 cu cm) Any 0-20 lb (0 to 9. 1 kg) 0-20 lb (0 to 9. 1 kg) 20-40 lb (9. 1 to 18. 1 kg) 60 in (1524 mm) 48 in (1219 mm) 42 in (1067 mm) 36 in (914 mm) Drives packaged in single or multipacks with a gross weight of 20 pounds (8. 95 kg) or less by Seagate for general freight shipment shall withstand a drop test from 48 inches (1, 070 mm) against a concrete floor or equivalent. Z Y X Z X Y Figure 12. Recommended mounting 34 Cheetah T10 SAS Product Manual, Rev. Operating--normal The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding 10-500 Hz @ 0. 5 G (zero to peak) Vibration may be applied in the X, Y, or Z axis. Operating normal translational random flat profile 10 - 500 Hz b. Operating--abnormal Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding: 15 minutes of duration at major resonant frequency 10-500 Hz @ 0. 75 G (X, Y, or Z axis) Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. This assumes system recovery routines are available. [. . . ] If your location is not listed here, dial our European CSO warranty center at +31-20-316-7222 from 8:30 A. M. (Central Europe time) Monday through Friday. The CSO warranty center is located in Amsterdam, The Netherlands. Seagate Service Centers Toll-free support numbers Call center Austria Belgium Denmark France Germany Ireland Italy Netherlands Norway Poland Spain Sweden Switzerland Turkey United Kingdom Presales and Technical Support -- 00 800-47324283 (00 800-4SEAGATE) 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-47324283 00 800-311 12 38 00 800-47324283 00 800-47324283 00 800-47324283 00 800-31 92 91 40 00 800-47324283 Warranty Service 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-47324289 00 800-311 12 38 00 800-47324289 00 800-47324289 00 800-47324289 00 800-31 92 91 40 00 800-47324289 FAX services--All Europe (toll call) Technical Support Warranty Service +1-405-324-3339 +31-20-653-3513 Cheetah T10 SAS Product Manual, Rev. A 75 Africa/Middle East support services For presales and technical support in Africa and the Middle East, dial our presales and technical support call center at +1-405-324-4714 from 8:00 A. M. [. . . ]