User manual MAXTOR DIAMONDMAX 21 PATA REV B 9-2007

[. . . ] Product Manual DiamondMax 21 PATA STM3320820A STM3300620A STM3250620A STM3250820A STM3200820A STM3160215A STM380215A 100451230 Rev. B September 2007 Revision status summary sheet Revision Date Sheets Affected Rev. B 11/16/06 09/21/07 Initial Release. Front cover, 1, 3, 8-13, 16-18, 22 and 33. Copyright © 2006, 2007 Seagate Technology LLC. [. . . ] Operation at excessive I/O duty cycle may degrade product reliability. The desktop personal computer environment of oower-on-hours, temperature, and I/O duty cycle affect the product AFR and MTBF. The AFR and MTBF will be degraded if used in a enterprise application. Nonrecoverable read errors Annualized Failure Rate (AFR) Contact start-stop cycles Warranty 1 per 1014 bits read, max 0. 34% (nominal power, 25°C ambient temperature) 50, 000 cycles (at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle) 3 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: http://www. seagate. com/support/service/ From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive. None required. Preventive maintenance 2. 13 2. 13. 1 Agency certification Safety certification The drives are recognized in accordance with UL 1950 and CSA C22. 2 (950) and meet all applicable sections of IEC950 and EN 60950. 2. 13. 2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products. 20 DiamondMax 21 PATA Product Manual, Rev. B Korean RRL If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea. These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recognized lab. · Family name: DiamondMax · Certificate number: Pending Australian C-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548 1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA). 2. 13. 3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc. ) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. [. . . ] predictability is limited to the attributes the drive can monitor. commands and implementation, see the Draft ATA-7 Standard. SeaTools diagnostic software activates a built-in drive self-test (DST S. M. A. R. T. command for D4H) that eliminates unnecessary drive returns. [. . . ]