User manual MAXTOR EGGM4013

[. . . ] Application Note: Interfacing non-standard cameras to Matrox Pulsar PerkinElmer (EG&G RETICON) MD4013 Camera Description § § § § § § June 16, 2000 1024 ´ 1024 ´ 8-bit @ 30 fps (maximum). Pixel clock: 20 MHz Control Interface Mode Camera Interface Briefs § Mode: Control VIDEO LEN FEN CCLK SHUT FST *Matrox RS-422 digital data input board § § § § § § § 1024 ´ 1024 ´ 8-bit. [. . . ] Matrox Pulsar sets the exposure time; the camera will expose for as long as the EXPOSURE2 (SHUT) signal is high. The camera initiates frame readout upon arrival of the falling edge of the EXPOSURE1 (FST) signal. The image captured by Matrox Pulsar resides scrambled in the host buffer and must be reconstructed. The original image is stretched and folded over; in the host buffer, the pixel columns from the second half of the original image are interleaved in a "folded paper" fashion with the pixel columns from the first half of the original image. The 30 ms immediately following the falling edge of the Frame Start signal cover the shift and readout of the entire array; therefore, in order to avoid smearing, the camera must not be triggered for a minimum of 30 ms after a Frame Start signal is received. PUL-CID-010 Application Note: Interfacing non-standard cameras to Matrox Pulsar June 16, 2000 PerkinElmer (EG&G RETICON) MD4013 Cabling Requirements Mode: Control · DBHD68-TO-OPEN (open end) cable and PULSAR/DIG/MOD board required for digital data, synchronization and control signals. TTL external trigger source should be connected to the TTL Trigger Input of the DBHD68TO-OPEN (open end) cable. Connections between the 68-pin connector of the camera and the 68-pin connector of the PULSAR/DIG/MOD are as follows: PULSAR/DIG/MOD (68-pin connector) Pin name CLKIN+ CLKINHSYNC+ HSYNCVSYNC+ VSYNCEXPOSURE1+ EXPOSURE1EXPOSURE2+ EXPOSURE2DATA0+ DATA1+ DATA2+ DATA3+ DATA4+ DATA5+ DATA6+ DATA7+ DATA0DATA1DATA2DATA3DATA4DATA5DATA6DATA7PULSAR/DIG/MOD (68-pin connector) Pin name DATA8+ DATA9+ continued ROPER SCIENTIFIC (EG&G) MD4013 (TOP DB-37 connector) Pin name Pin no. CCLK+ 01 CCLK20 LEN+ 02 LEN21 FEN+ 03 FEN22 FST+ 24 FST05 SHUT+ 06 SHUT25 ADATA0 08 ADATA1 09 ADATA2 10 ADATA3 11 ADATA4 12 ADATA5 13 ADATA6 14 ADATA7 15 BDATA0 27 BDATA1 28 BDATA2 29 BDATA3 30 BDATA4 31 BDATA5 32 BDATA6 33 BDATA7 34 ROPER SCIENTIFIC (EG&G) MD4013 (BOTTOM DB-37 connector) Pin name Pin no. ADATA0 08 ADATA1 09 · · Pin no. 29 63 26 60 25 59 30 64 28 62 20 19 16 15 14 13 11 10 54 53 50 49 48 47 45 44 Pin no. 09 08 PUL-CID-010 2 Application Note: Interfacing non-standard cameras to Matrox Pulsar June 16, 2000 PerkinElmer (EG&G RETICON) MD4013 Cabling Requirements (continued) PULSAR/DIG/MOD (68-pin connector) Pin name DATA10+ DATA11+ DATA12+ DATA13+ DATA14+ DATA15+ DATA8DATA9DATA10DATA11DATA12DATA13DATA14DATA15· Pin no. 07 06 05 04 03 02 43 42 41 40 39 38 37 36 ROPER SCIENTIFIC (EG&G) MD4013 (TOP DB-37 connector) Pin name Pin no. [. . . ] Contact your local sales representative or Matrox Sales office or Imaging Applications at 514-822-6061 for assistance. Corporate headquarters: Canada and U. S. A. Dorval, Quebec H9P 2T4 Canada Tel: (514) 685-2630 Fax: (514) 822-6273 PUL-CID-010 [. . . ]