User manual MAXTOR M16I

[. . . ] CAMERA INTERFACE APPLICATION NOTE REDLAKE MASD (KODAK) 1. 6i JUNE 19, 2001 Basics about the camera MATROX PULSAR Camera Descriptions § § § § § § 1534 × 1024 × 10-bit @ 5 fps (maximum). Single channel RS-422 digital video output. [. . . ] PIX DATA EXPOSE Specifics about the interface modes Camera Interface Details Mode 1: Pseudo-continuous TTL EXTERNAL TRIGGER *Matrox Pulsar RS-422 digital data input board § Frame Rate: Matrox Pulsar receives the continuous video from the camera at 10 frames per second. § Exposure time: Exposure time is controlled by the Remote Panel software. Refer to the camera manual for more information. § Remote Panel software settings: Settings for this mode are as follows: DEF on GAB -22 BKB 0 BKE 0 MDE PI EXE 15. 096 STP P TRM P TRS AIA TRE 1 RDM 1 TPD 255 TPW 5 DGN 2 Mode 2: Asynchronous Reset (Trigger) § Frame rate: The frame rate is determined by the frequency of the external trigger signal. § Exposure time: Exposure time is controlled by the Remote Panel software. Refer to the camera manual for more information. § Remote Panel software settings: Settings for this mode are as follows: DEF on GAB -22 BKB 0 BKE 0 MDE TR EXE 15. 096 STP P TRM P TRS AIA TRE 1 RDM 1 TPD 255 TPW 5 DGN 2 Mode 2: Asynchronous Reset (Control) § Frame rate: The frame rate is determined by the frequency of the external trigger signal. § Exposure time: The width (rising to falling edge) of the EXPOSURE1 (EXPOSE) signal initiates and controls the exposure. The exposure time can be modified in the DCF using Matrox Intellicam or with the MIL MdigControl() function. Consult the manual for more information. § Remote Panel software settings: Settings for this mode are as follows: DEF on GAB -22 BKB 0 BKE 0 MDE CD EXE 15. 096 STP P TRM P TRS AIA TRE 1 RDM 1 TPD 255 TPW 5 DGN 2 PUL-CID-047 2 CAMERA INTERFACE APPLICATION NOTE REDLAKE MASD (KODAK) 1. 6i JUNE 19, 2001 Cabling details for this interface mode MATROX PULSAR Cabling Requirements Mode 1: Pseudo-continuous § Cable: DBHD68-TO-OPEN (open ended) cable required for video, synchronization and control signals. § Connection: Connections between the 68-pin connector of the camera and the 68-pin connectors of the Matrox Pulsar are as follows: PULSAR/DIG/MOD (68-pin connector) Pin name Pin no. REDLAKE MASD 1. 6i (68-pin connector) Pin name Pin no. DATA9+ 08 MSB+ 02 DATA942 MSB36 DATA8+ 09 MSB-1+ 03 DATA843 MSB-137 DATA7+ 10 MSB-2+ 04 DATA744 MSB-238 DATA6+ 11 MSB-3+ 05 DATA645 MSB-339 DATA5+ 13 MSB-4+ 06 DATA547 MSB-440 DATA4+ 14 MSB-5+ 07 DATA448 MSB-541 DATA3+ 15 MSB-6+ 08 DATA349 MSB-642 DATA2+ 16 MSB-7+ 09 DATA250 MSB-743 DATA1+ 19 MSB-8+ 10 DATA153 MSB-844 DATA0+ 20 MSB-9+ 11 DATA054 MSB-945 CLKIN+ 29 PIX DATA STRB+ 29 CLKIN63 PIX DATA STRB63 HSYNC+ 26 LINE ENA+ 26 HSYNC60 LINE ENA60 VSYNC+ 25 FRME ENA+ 25 VSYNC59 FRME ENA59 EXPOSURE1+ 30* EXPOSE+ 30* EXPOSURE164* EXPOSE64* TTL_USR0 31 MC0 31 TTL_USR1 32 MC1 32 TTL_USR2 33 MC2 33 GROUND 1 -GROUND 01 GROUND 12 -GROUND 12 * Connection not necessary for this mode however allows this cable to be used for both modes. Continued. . . PUL-CID-047 3 CAMERA INTERFACE APPLICATION NOTE REDLAKE MASD (KODAK) 1. 6i JUNE 19, 2001 Cabling details for this interface mode MATROX PULSAR Cabling Requirements(Continued) Mode 1: Pseudo-continuous PULSAR/DIG/MOD (68-pin connector) Pin name GROUND GROUND GROUND GROUND Pin no. [. . . ] Contact your local sales representative or Matrox Sales office or Matrox Imaging Applications at 514-822-6061 for assistance. Corporate headquarters: Canada and U. S. A. Dorval, Quebec H9P 2T4 Canada Tel: (514) 685-2630 Fax: (514) 822-6273 PUL-CID-047 [. . . ]