User manual MAXTOR MEDALIST PRO 6530

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Pro 9140 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Pro 6530 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist Pro 4520 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ultra ATA Interface Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Die Versorgungsspannung muss SELV entsprechen. Alle Arbeiten an der Festplatte dürfen nur von ausgebildetem Servicepersonal durchgeführt werden. Bitte entfernen Sie nicht die Aufschriftenschilder des Laufwerkes. Der Einbau des Laufwerkes muss den Anforderungen gemäss DIN IEC 950 VDE 0805/05. 90 entsprechen. Medalist Pro 9140, 6530 and 4520 Product Manual, Rev. B 17 2. 0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 2. 1 Handling and static-discharge precautions After you unpack the drive, and before you install it in a system, be careful not to damage it through mishandling. Observe the following standard handling and static-discharge precautions: Caution: · Keep the drive in its static-shielded bag until you are ready to complete the installation. Do not attach any cables to the drive while it is in its static-shielded bag. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Handle the drive by its edges or frame only. · The drive is extremely fragile--handle it with care. Do not press down on the drive top cover. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. 18 Medalist Pro 9140, 6530 and 4520 Product Manual, Rev. B 2. 2 I/O cable and connector The drive uses a 40-pin, male I/O connector with two rows of twenty pins each and a notch for keying. A drawing of the I/O connector is shown in Figure 2. Pin 1 is located near the 4-pin power connector when the I/O connector is mounted. 0. 100 ± 0. 010 0. 70 ± 0. 010 0. 235 ± 0. 025 pin 1 0. 230 ± 0. 003 0. 025 ± 0. 002 0. 025 ± 0. 002 0. 160 1. 90 2. 00 0. 100 typ 0. 070 ± 0. 010 Figure 2. ATA interface connector The table below lists recommended parts for the mating connector. Part Connector Connector Flat cable Description 40-pin 40-pin AWG28 (stranded) 3M part number 3M-3417-7000 3M-3448-2040 3M-3365-40 To ensure the integrity of your data, use a 40-connector, nonshielded I/O cable with a maximum length of 18 inches (46 centimeters). 2. 3 Power connector The drive uses a standard 4-pin, male power connector. [. . . ] · A receiver must be prepared to receive at least two words of data whenever it enters or resumes a burst mode. · During the entire burst, ­CS0, ­CS1, and ­IOCS16 are in the high negated state. · The drive begins driving and stops tristating IORDY when ­DMACK is first asserted and SyncDMA is enabled. The drive must continue to Medalist Pro 9140, 6530 and 4520 Product Manual, Rev. [. . . ]