User manual MAXTOR MI140010S

[. . . ] Application Note: Xillix Mi 1400-10S Camera Descriptions · · Interfacing non-standard cameras to Matrox Pulsar June 20, 1997 1318 x 1037 X 10-bits @ 5 fps (max) Digital video output (RS-422). [. . . ] TTL external trigger · Non-interlaced · Matrox Pulsar receiving RS-422/TTL external trigger signal · Matrox Pulsar sending exposure signal to camera · Matrox Pulsar receiving RS-422 hysnc, vsync, pixel clock, and line clock signals from camera · DCFs used: MI1400D. DCF · Application Note: Xillix Mi 1400-10S Interfacing non-standard cameras to Matrox Pulsar June 20, 1997 Cabling Requirements Mode 1: Trigger mode (Software) PULSAR/DIG/MOD required for digital data and syncs in RS-422 format. · The following connections should be made between the 50-pin RS-422 PCB connector of the camera and the 68-pin connector of the PLS/CBL/OPEN: · PLS/CBL/OPEN (PULSAR) (68-pin connector) Pin name GROUND DATA0+ DATA1+ DATA2+ DATA3+ DATA4+ DATA5+ DATA6+ DATA7+ DATA8+ DATA9+ DATA10+ DATA11+ GROUND DATA0DATA1DATA2DATA3DATA4DATA5DATA6DATA7DATA8DATA9DATA10DATA11GND TTL_USER0 TTL_USER0 TTL_USER0 GND GND HSYNC+ HSYNCCLKIN+ CLKINEXPOSURE1+ EXPOSURE1(continued) Pin no. 12 20 19 16 15 14 13 11 10 9 8 7 6 46 54 53 50 49 48 47 45 44 43 42 41 40 1 31 31 31 68 68 26 60 29 63 30 64 Xillix Mi1400-10S (50-pin PCB connector) Pin name GND DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 DATA 8 DATA 9 DATA 10 DATA 11 DATA 12 GND DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 DATA 8 DATA 9 DATA 10 DATA 11 DATA 12 MODE MODE FREQ 1 FREQ 2 FREQ 1 FREQ 2 LINE CLOCK LINE CLOCK PIXEL CLOCK PIXEL CLOCK EXPOSURE EXPOSURE Pin no. 1 2 3 4 5 6 7 8 9 10 11 12 13 26 27 28 29 30 31 32 33 34 35 36 37 38 17 42 15 16 40 41 19 44 22 47 24 49 PUL-CID-040 2 Application Note: Xillix Mi 1400-10S GROUND GROUND DATA 12+ DATA13+ DATA 14+ DATA 15+ DATA 12DATA 13DATA 14DATA 15TTL_USR1 Interfacing non-standard cameras to Matrox Pulsar June 20, 1997 34 35 5 4 3 2 39 38 37 36 32 GND GND GND GND GND GND 18 43 18 18 43 43 Cabling Requirements (continued) Mode 2: Trigger mode (external) All connections are the same as in Mode 1: (Trigger mode -software) except that IMG-7W2TO-5BNC required for TTL external trigger source and TTL external trigger source should be connected to the TTL Trigger Input of the IMG-7W2-TO-5BNC cable. The DCF(s) mentioned in this application note can be found on the MIL and MIL-Lite CD, or our FTP site (ftp. matrox. com). The information furnished by Matrox Electronics System, Ltd. is believed to be accurate and reliable. Please verify all interface connections with camera documentation or manual. Contact your local sales representative or Matrox Sales office or Matrox Imaging Applications at 514-822-6061 for assistance. Corporate Headquarters: Canada and U. S. A. [. . . ] Tel: 852. 2877. 5387 Fax: 852. 2537. 9530 PUL-CID-040 3 [. . . ]