User manual MAXTOR SMD4M15

[. . . ] Application Note: SMD 4M15 Camera Descriptions · · · · · · Interfacing non-standard cameras to Matrox Genesis February 16, 1998 2048 x 2048 x 12-bit @ 15 fps. 4-channel digital video output (RS-422). Maximum data rate per output: 15 MB/s N. B. [. . . ] DCF used : SMDC2X2. DCF Note: requires two additional programs for operation (see Camera Interface Details) GEN-CID-031 Application Note: SMD 4M15 Interfacing non-standard cameras to Matrox Genesis February 16, 1998 Camera Interface Briefs (continued) Mode 3: Continuous (4x4 Binning) Video SMD 4M15 HSYNC VSYNC Pixel Clock Matrox Genesis (GEN/_/_/STD* + GEN/DIG/BRD/S**) · · · · · · · · 512 x 512 x 8-bit @ 46 fps. * Matrox Genesis Main Board with Grab Module 4-channel digital video output (RS-422). ** Matrox Digital Data Input Board Non-interlaced (progressive scan). Pixel clock frequency: 5 MHz Matrox Genesis receiving RS-422 HSYNC, VSYNC and pixel clock signals from camera. DCF used : SMDC4X4. DCF Note: requires two additional programs for operation (see Camera Interface Details) Mode 4: Continuous (AOI -Area Of Interest) Video SMD 4M15 HSYNC VSYNC Pixel Clock Matrox Genesis (GEN/_/_/STD* + GEN/DIG/BRD/S**) · · · · · · · · * Matrox Genesis Main Board 1024 x 256 x 8-bit @ 15 fps. with Grab Module 4-channel digital video output (RS-422). ** Matrox Digital Data Input Board Interlaced. Pixel clock frequency: 10 MHz Matrox Genesis receiving RS-422 HSYNC, VSYNC and pixel clock signals from camera. DCF used : SMDCAOI. DCF Note: requires two additional programs for operation (see Camera Interface Details) Camera Interface Details Modes 1-4: Data connections and image viewed from front Camera Rear A B POWER DATA 1 DATA 2 DATA 1 DATA 2 GEN-CID-031 2 Application Note: SMD 4M15 Interfacing non-standard cameras to Matrox Genesis February 16, 1998 Camera Interface Details (continued) Modes 1-4: Continuous (no Binning, 2x2 Binning, 4x4 Binning, AOI) · · · In addition to the corresponding DCF file, two supplementary programs are required to operate the camera with the Matrox Genesis: comserial. c (to write data to the PC serial port) and grabsmd. c (to control the Matrox Genesis grabbing). Programming the serial port requires the following usage: "comserial -x addr data" (hexadecimal values) or "comserial -d addr data" (decimal values) Operating Modes: Address 0x81 of the camera controls the principle operating modes. No Binning : comserial -x 81 02 2x2 Binning: comserial -x 81 06 4x4 Binning: comserial -x 81 0a AOI mode : comserial -x 81 42 Mode 4: Continuous (AOI -Area Of Interest) · Start/End registers Addresses 0x89 and 0x8a control the START readout register. Addresses 0x8c and 0x8b control the END readout register. The commands below indicate that the readout will start at line 0x30f (783) and end at 0x410 (1040) for a total of 256 lines read out (per tap). comserial -x 8a 0f comserial -x 89 03 comserial -x 8c 10 comserial -x 8b 04 · For more information and options refer to the readme. txt file included with the DCFs and demo program or contact Matrox Imaging Applications at 514-822-6061 for assistance. GEN-CID-031 3 Application Note: SMD 4M15 Interfacing non-standard cameras to Matrox Genesis February 16, 1998 Cabling Requirements Modes 1-4: Continuous (no Binning, 2x2 Binning, 4x4 Binning, AOI) · · GEN-DIG-BRD/S required for digital data, syncs and control signals in RS-422 format. [. . . ] SL2 4JS Tel: +44 (0) 1753 665500 Fax: +44 (0) 1753 665599 France Matrox France SARL 2, rue de la Couture, Silic 225 94528 Rungis Cedex Tel: (0) 1 45-60-62-00 Fax: (0) 1 45-60-62-05 Germany Matrox GmbH Inselkammerstr. 8 D-82008 Unterhaching Germany Tel: 089/614 4740 Fax: 089/614 9743 Asia Pacific Matrox Asia Liaison Office Rm. 1901, 19/F, Workington Tower, 78 Bonham Strand E. , Sheung Wan, Hong Kong. Tel: 852. 2877. 5387 Fax: 852. 2537. 9530 GEN-CID-031 5 [. . . ]