User manual MAXTOR ST31051N INSTALLATION

[. . . ] HAWK 2XL Family: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST32151N/W/WC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST31051N/W/WC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST32155N/W/WC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use the antistatic pad as your work surface, and avoid installation in areas with staticinducing carpets. Begin by removing the cover of the computer. Follow the instructions in your computer manual. Systems that use "WC" drives probably do not require cover removal, as the drives are mounted in a module that slides into place and plugs in. Hawk 2XL Family Installation Guide, Rev. C 2. 23 _______________________________________________________________________________________________________________________ Does your system have 5. 25-inch drive bays?Your Seagate drive is designed to fit into a 3. 5-inch wide drive bay. If your computer has 5. 25-inch drive bays, then you must mount the drive ("N" or "W" models only) in a conversion frame kit before then you must mount the drive ("N" or "W" models only) in a conversion frame kit before it will fit into your computer. Purchase a conversion frame kit from your computer dealer if necessary. Connect the 50 or 68 pin interface cable to the hard drive interface connector on the SCSI host adapter card. Be careful not to bend the pins on the host adapter card connector. Refer to your SCSI host adapter manual for the location of the interface connector. The sockets on the interface cable must be matched correctly with the pins on your SCSI host adapter interface connector. Verify the location of pin 1 on the SCSI host adapter using your computer system's manual. Pin 1 on the interface cable is indicated by the stripe along the edge of the cable. Plug the cable into the hard drive interface connector on your SCSI host adapter. 3. 4. Thread the other end of the interface cable through your drive bay and connect to the disc drive, as shown in Figure 4a, 4b, 4c or 4d. The sockets on the interface cable must be matched correctly with the pins on the disc drive. Pin 1 on the interface cable is indicated by the strip along the edge of the cable; 24 Hawk 2XL Family Installation Guide, Rev. C pin 1 on the Seagate disc drive is the pin closest to the HDA, on the side closest to the four-pin powersupply connector as shown in Figure 4a or 4b. Plug the interface cable into the drive connector firmly but carefully. The connector should cover both rows of pins. If you are installing a second or multiple disc drives, repeat this procedure using the additional drive connectors on the interface cable, as shown in Figures 4c or 4d. _______________________________________________________________________________________________________________________ 5. Mount the drive in a drive bay. · Direct mounting: The disc drive can be mounted in the drive bay in any orientation permitted by the drive bay mechanical configuration. Be careful not to over tighten the mounting screws. [. . . ] Product Technical Support is available for all Seagate products by calling the SeaFAX, SeaFONE, SeaTDD or SeaBOARD services. SeaBOARDTM: the Seagate Technical Support Bulletin Board System (BBS) is available by modem 24 hours a day, 7 days a week. SeaBOARD provides access to: · Specifications and configurations for all Seagate products · Reprints of Seagate documentation · A directory of information and useful utilities that can be downloaded to your computer To access SeaBoard: · Set your communications software to eight data bits, no parity, and one stop bit (8-N-1). · Dial the nearest SeaBOARD number from the following list: Hawk 2XL Family Installation Guide, Rev. [. . . ]