User manual MAXTOR ST32430W VOLUME 1

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HAWK 2LP Family: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Wide bus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST32430W/WD/WC/DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST31230W/WD/WC/DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual, Volume 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HAWK 2LP Family: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Wide bus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST32430W/WD/WC/DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST31230W/WD/WC/DC Product Manual, Volume 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . © 1996 Seagate Technology, Inc. All rights reserved Publication Number: 77767480, Revision E March 1996 Seagate®, Seagate Technology®, and the Seagate logo are registered trademarks of Seagate Technology, Inc. [. . . ] Orientation of the side nearest the LED may be up or down. Operating The drive, as installed for normal operation, shall operate error free while subjected to intermittent shock not exceeding 10 g's at a maximum duration of 11 ms (half sinewave). Shock may be applied in the X, Y, or Z axis. Nonoperating The limits of nonoperating shock shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives. The drive subjected to nonrepetitive shock not exceeding 75 g's at a maximum duration of 11 ms (half sinewave) shall not exhibit device damage or performance degradation. Shock may be applied in the X, Y, or Z axis. Packaged Disc drives shipped as loose load (not palletized) general freight will be packaged to withstand drops from heights as defined in the table below. For additional package requirements refer to Seagate specifications 30190-001 (under 100 lbs) or 30191-001 (over 100 lbs). (kg) Any 0-20 (0 to 9. 1) 0-20 (0 to 9. 1) 20-40 (9. 1 to 18. 1) Package Size (Cu. In. ) <600 600-1800 >1800 >600 Drop Height in. mm 60 (1524) 48 (1219) 42 (1067) 36 (914) Product Manual - Hawk 2LP Family (Wide) SCSI-2 (Volume 1) Rev. E 23 _____________________________________________________________________________________ B A E A1 D C D1 C1 SE AG AT E Z Y X Figure 7. 4. 4-1. Recommended mounting SE AG AT E B1 B1 A1 B A Z X Y E1 E1 D1 C1 E D C 24 Product Manual - Hawk 2LP Family (Wide) SCSI-2 (Volume 1), Rev. E _____________________________________________________________________________________ 7. 4. 4. 2 Vibration a. Operating The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding 5-22 Hz @ 0. 020 inches (0. 51 mm) displacement 22-400 Hz @ 0. 5 g Vibration may be applied in the X, Y, or Z axis. Nonoperating The limits of nonoperating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives. The drive shall not incur physical damage or degraded performance as a result of continuous vibration not exceeding 5-22 Hz @ 0. 081 inches (2. 05 mm) displacement 22-400 Hz @ 2. 00 g Vibration may be applied in the X, Y, or Z axis. 7. 4. 5 Air cleanliness The drive is designed to operate in a typical office environment with minimal environmental control. 7. 5 7. 5. 1 Electromagnetic compatibility Electromagnetic susceptibility As a component assembly, the drive is not required to meet any susceptibility performance requirements. It is the responsibility of the system integrator to perform those tests required to ensure that equipment operating in the same system as the drive does not adversely affect the performance of the drive. See section 6. 1. 2, and see Table 7. 2-1, DC Power Requirements. Product Manual - Hawk 2LP Family (Wide) SCSI-2 (Volume 1), Rev. [. . . ] It also includes basic information to assist in obtaining service for the drive. 66 Product Manual - Hawk 2LP Family (Wide) SCSI-2 (Volume 1), Rev. E _____________________________________________________________________________________ 13. 0 Accessories All accessories are designed for implementation by the customer. 13. 1 Front panel kit Same as 12. 1 but includes all mounting hardware to support field installation. 13. 2 Installation Guide The Installation Guide (P/N 77767478) is usually included with each drive shipped, but extra copies may be ordered. Product Manual - Hawk 2LP Family (Wide) SCSI-2 (Volume 1), Rev. [. . . ]