User manual MAXTOR ST5660A

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST5660A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AT Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST5660A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AT Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 950 · Certified to VDE 0805/05. 90 and EN 60950/1. 88 as tested by VDE 1. 11 FCC verification The ST5660A drive is intended to be contained solely within a personal computer or similar enclosure (not attached to an external device). As such, a drive is considered to be a subassembly even when individually marketed to the customer. As a subassembly, no Federal Communications Commission authorization, verification or certification of the device is required. has tested these drives in an enclosure as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc. ) does comply with the limits for a Class B computing device, pursuant to Subpart J of Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interference to radio and television reception. This equipment generates and uses radio frequency energy and, if not installed and used in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television, which can be determined by turning the equipment on and off, you are encouraged to try one or more of the following corrective measures: · Reorient the receiving antenna. · Move the device to one side or the other of the radio or TV. · Move the device farther away from the radio or TV. · Plug the equipment into a different outlet so that the receiver and computer are on different branch outlets. 12 ST5660A Product Manual, Rev. A If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4. This digital apparatus does not exceed the Class B limits for radio noise emissions from computer equipment as set out in the radio interference regulations of the Canadian Department of communications. Le présent appareil numérique német pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. Sicherheitsanleitung 1. Das Gerrät ist ein Einbaugerät, das für eine maximale Umegebungstemperatur von 55°C vorgesehen ist. Zur Befestigung des Laufwerks werden 4 Schrauben 6-32 UNC-2A benötigt. Bei seitlicher Befestigung darf die maximale Länge der Schrauben im Chassis nicht mehr als 5, 08 mm und bei Befestigung an der Unterseite nicht mehr als 5, 08 mm betragen. Als Versorgungsspannugen werden benötigt: +5V ± 5% 0, 65A +12V ± 5% 0, 45A (1, 9A fur ca. [. . . ] The head parameter is not valid for this command. D Command name Active and Set Idle Timer Active Immediate Check Idle Mode Check Power Mode Execute Drive Diagnostics Format Track continued Parameters used Command code (in hex) FR SC SN CY DH FB F9 FD 98, E5 90 50 n n n n n n y n y y n y n n n n n n n n n n n y D D D D D y 22 continued from previous page ST5660A Product Manual, Rev. A Command name Identify Drive Idle Idle and Set Idle Timer Idle Immediate Initialize Drive Parameters Read DMA Read Long Read Multiple Read Sector Read Sector Buffer Read Verify Sector Recalibrate Seek Set Features Set Multiple Mode Sleep Standby Standby Immediate Write DMA Write Long Write Multiple Write Sector Write Sector Buffer Parameters used Command code (in hex) FR SC SN CY DH EC 97, E3 FA 95, F8, E1 91 C8, C9 22, 23 C4 20, 21 E4 40, 41 1X 7X EF C6 99, E6 96, E2 94, E0 CA, CB 32, 33 C5 30, 31 E8 n n n n n -- n n n n n n n y n n n n -- n n n n n y y n y y y y y n y n n n y n n n y y y y n n n n n n y y y y n y n y n n n n n y y y y n n n n n n y y y y n y n y n n n n n y y y y n D D D D y y y y y D y D y D D D D D y y y y D ST5660A Product Manual, Rev. A 23 3. 1. 1 Identify Drive command (ECH) The parameters for the drive are listed in the table below. The Seagate ATA Interface Reference Manual, publication number 36111-xxx, describes the Identify Drive command in detail. [. . . ]