User manual MAXTOR ST9100AG INSTALLATION

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . ST9100A . . . . . . . . . . . . . . . . . . . . . . . . . . AT Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . Contents Read before you begin. . . . Setting master/slave jumpers Connecting cables Mounting the drive 1 Installation overview . 5 Formatting and partitioning the drive . [. . . ] To avoid damaging the drive: · Use M3X0. 5 metric mounting screws only. · Do not insert mounting screws more than 0. 150 inches (3. 81 mm) into the mounting holes. · Do not overtighten the screws (maximum torque: 3 inch-lb). Allow a minimum clearance of 0. 030 inches (0. 762 mm) around the entire perimeter of the drive for cooling airflow. Mounting dimension drawings for the ST9100 drives are provided in Appendix B. Most ST9100A and all ST9100AG drives conform to the industry-standard MCC mounting specification. Refer to the ST9100A and ST9100AG Product Manual (Seagate Publication 36211-001) for details. Configuring system BIOS Before the host system can recognize a new drive, it must be provided with basic information about the drive into the host system BIOS. Specifically, you need to know the number of cylinders, heads, and sectors, as well as the overall capacity of the drive you are installing. The table on page 6 lists these specifications for the ST9100A and ST9100AG. It is not necessary to understand these terms to set up the system BIOS. Read your system documentation or run your system setup program (described on the following page) to determine which drive types your BIOS supports. Another method is to run the FINDTYPE. EXE utility program, available from Seagate Techni- 6 ST9100A and ST9100AG Installation Guide, Rev. A cal Support services (on the SeaBOARD BBS) as described in Appendix C. The methods used to configure system BIOS vary from system to system. In many cases, you can run a setup program from the DOS prompt. In other cases, you must initiate BIOS setup by pressing certain keys while the system is booting up. Within the setup program, there are three possible ways that you can specify your drive type: · Match your drive specifications (from the table below) with those of a drive type specified in the setup program. · Specify a custom or user-defined drive type in the setup program, then manually enter your drive specifications from the table below. · Select specifications lower than those required for your drive, and allow your drive to mimic the drive type selected. sectors Capacity (Mbytes) BIOS calculated Usable ST9100A and ST9100AG 748 14 16 167, 552 81. 8 85. 8 When the drive specifications are entered manually as a userdefined or custom drive type, the BIOS should display a drive capacity equal to the BIOS calculated capacity in the table above. This value will be lower than the usable drive capacity. ST9100A and ST9100AG Installation Guide, Rev. A 7 In a few situations, none of the drive types specified in your BIOS setup program will match your drive, and the setup program will not provide an opportunity to specify a custom drive type. [. . . ] AT interface connector pin assignments Drive pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 *28 29 30 31 32 33 *34 35 36 37 38 *39 40 Signal name Reset­ Ground DD7 DD8 DD6 DD9 DD5 DD10 DD4 DD11 DD3 DD12 DD2 DD13 DD1 DD14 DD0 DD15 Ground (removed) DMARQ Ground DIOW­ Ground DIOR­ Ground IORDY SPSYNC:CSEL DMACK­ Ground INTRQ IOCS16­ DA1 PDIAG­ DA0 DA2 CS1FX­ CS3FX­ DASP­ Ground Host pin # and signal description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Host Reset Ground Host Data Bus Bit 7 Host Data Bus Bit 8 Host Data Bus Bit 6 Host Data Bus Bit 9 Host Data Bus Bit 5 Host Data Bus Bit 10 Host Data Bus Bit 4 Host Data Bus Bit 11 Host Data Bus Bit 3 Host Data Bus Bit 12 Host Data Bus Bit 2 Host Data Bus Bit 13 Host Data Bus Bit 1 Host Data Bus Bit 14 Host Data Bus Bit 0 Host Data Bus Bit 15 Ground (No Pin) DMA Request Ground Host I/O Write Ground Host I/O Read Ground I/O Channel Ready Spindle sync or Cable Select DMA Acknowledge Ground Host Interrupt Request Host 16 Bit I/O Host Address Bus Bit 1 Passed Diagnostics Host Address Bus Bit 0 Host Address Bus Bit 2 Host Chip Select 0 Host Chip Select 1 Drive Active/ Drive 1 Present Ground *Indicates master-slave signals (details shown below). Drive 1 (slave) 28 34 39 Drive 0 (master) 28 34 39 Host SPSYNC:CSEL PDIAG­ DASP­ 28 34 39 12 ST9100A and ST9100AG Installation Guide, Rev. Mounting dimensions 0. 489 ± 0. 015 (12. 42 ± 0. 38) Dimensions are in inches (mm) 0. 039 ± 0. 020 (0. 99 ± 0. 51) 0. 000 in (mm) 4X 3 mm × 0. 5 mm, 0. 15 in (3. 81mm) min. full thread 1. 227 ± 0. 025 (31. 17 ± 0. 61) 3. 986 ± 0. 015 (101. 24 ± 0. 38) 0. 118 ± 0. 010 (3. 00 ± 0. 25) 0. 146 +0. 011, ­0. 008 (3. 71 +0. 28, ­0. 20) 1. 500 ± 0. 010 (38. 10 ± 0. 25) 0. 000 1. 375 ± 0. 015 (34. 93 ± 0. 38) 0. 155 ± 0. 020 (3. 94 ± 0. 51) 0. 000 0. 239 ± 0. 035 (6. 07 ± 0. 89) 2. 740 ± 0. 020 (69. 60 ± 0. 51) 2. 430 ± 0. 010 (61. 72 ± 0. 25) 4X 3 mm × 0. 5 mm, 0. 15 in (3. 81 mm) min. [. . . ]