Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAXTOR XC55. We hope that this MAXTOR XC55 user guide will be useful to you.
Lastmanuals help download the user guide MAXTOR XC55.
Detailed instructions for use are in the User's Guide.
[. . . ] Application Note:
SONY XC-55
Camera Descriptions
· · · · ·
Interfacing non-standard cameras to Matrox Pulsar July 18, 2000
646 × 485 × 8-bits. [. . . ] DCF used: XC55NA. DCF
PUL-CID-052
Interfacing non-standard cameras to Matrox Pulsar SONY XC-55
Camera Interface Details Camera Switch settings (External /Internal) Mode 1: Continuous (Interlaced) 1l / Factory settings Mode 2: Continuous (Progressive scan) 1N / Factory settings Mode 3: Asynchronous reset (E-DONPISHA-II) 1N / S2 = E Mode 2: Asynchronous reset (E-DONPISHA-II)
· · ·
Application Note:
July 18, 2000
·
The frame rate is determined by the period of the TTL external trigger. The external trigger is input on the Matrox Pulsar via the analog trigger input. Once this external trigger is received, the Matrox Pulsar generates an EXPOSURE1 (TRIGGER) pulse, which in turn initiates camera exposure. The exposure time is the EXPOSURE1 (TRIGGER) period plus a fixed internal camera delay of 8 µsec.
TTL External Trigger Exposure Time EXPOSURE1 (TRIGGER) Delay 8 ms Exposure2 (VD)
Video (Video Out)
Video Valid
Cabling Requirements
Mode 1: Continuous
·
IMG-7W2-TO-5BNC (red BNC) or IMG-7W2-TO-1BNC cable required for video output of camera.
Mode 2: Asynchronous reset (E-DONPISHA)
·
·
·
IMG-7W2-TO-5BNC and PLS-TTL-CABLE cables required for TTL external trigger signal and for video output of camera. TTL external trigger source should be connected to the TTL trigger input of the IMG-7W2TO-5BNC cable. Connections between the 37-pin connector of the Matrox Pulsar (PLS-TTL-CABLE) and the 12-pin connector of the camera are as follows:
Matrox Pulsar (37-pin connector) Pin name TTL_ EXPOSURE1 TTL_ EXPOSURE2 GROUND TTL_ HSYNC continued Sony XC-55 (12-pin connector) Pin name EXT. 09 07 08 06
PUL-CID-052
2
Interfacing non-standard cameras to Matrox Pulsar SONY XC-55
Power Supply Pin name + 12 volts GROUND Sony XC-55 (12-pin connector) + 12 volts GROUND
Application Note:
July 18, 2000
Cabling Requirements (continued)
---
---
11 10
The DCF(s) mentioned in this application note can be found on the MIL and MIL-Lite CD, or our FTP site (ftp. matrox. com). The information furnished by Matrox Electronics System, Ltd. [. . . ] Dorval, Quebec H9P 2T4 Canada Tel: (514) 685-2630 Fax: (514) 822-6273
PUL-CID-052
3 [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MAXTOR XC55
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAXTOR XC55 will begin.
