User manual MAYTAG MDE1100AES

[. . . ] Use and Care Guide Drying cabinet MDE 1100AES Dear MAYTAG customer!Congratulations on your excellent product choice and welcome to the Maytag family. A global family with its roots in Scandinavia. Cleaning results, design, environmental impact on nature and home, user friendliness, low consumption of time, energy and water, a long life span, reliability. . . . [. . . ] Humid air out Hose Exhaust collar Draft stabilizer Air intake Ventilation duct valve 1 5 2 3 The drying cabinet is connected to the evacuation duct with a draft stabilizer 10 Permanently installed and connected to a vent duct (only certain markets) When the drying cabinet is permanently connected to the vent duct, the entire room is ventilated through the drying cabinet. The ventilation duct valve is replaced by an adapter (not included). See also the section 'Connect Ventilation' page 17. ATTENTION Only the evacuation hose delivered with the cabinet must be used. (For the markets where such an article is included) Do not assemble the ventilation duct valve inside the drying cabinet. 3 1 1. Ventilation duct valve 2 The drying cabinet permanently installed and connected to the evacuation duct 11 Installation Unpacking WARNING The cabinet can easily tip over since it is not yet solidly screwed into place. WARNING The packing material such as plastic or frigolite should be kept out of children´s way. Take off all the packing material; do not use a sharp tool which could damage the product. Check that the drying cabinet has not been damaged during transportation. The distributor should be notified of any damage during transportation within 7 days. After unpacking, check that the drying cabinet is free from defects. The distributor should immediately be notified of any damage, defects or even missing parts. Check that all the safety devices used for transportation have been removed before the drying cabinet is connected. Complete delivery includes The cabinet with the fan unit Flexible hose for ventilation (only certain markets) Exhaust collar with 2 attachment screws Draft stabilizer (only certain markets) Attachment screws (2 screws, washers and protective caps) for firmly fixing the cabinet to the wall Allen wrench and protective caps for the adjustable feet The Use and Care Guide for installation and utilisation Recommended tools Bubble level Tape measure Hand drill Screwdriver (Phillips) An 8 mm diameter drill bit Pencil Protective gloves (if supplied) 12 Placing the door the other way round The door can be hung on its hinges on the left or the right. Lay the drying cabinet on its back side. Disengage the hinge pin of the bottom hinge (1) and lift the door off. Take off the plastic plug and press it right down on to the bottom hinge on the opposite side. Disengage the hinge pin of the upper hinge (2) and place it on the opposite side. Completely unscrew the glove hangers on the inside of the door and turn them completely around. The glove hangers are fastened into place with four screws. Rotate the door, fit it into place and fix it firmly by means of the lower hinge pin (1). 2 1 13 Horizontal adjustment 1. Minimum air gap 10 mm between drying cabinet and mounting unit (above and behind the drying cabinet) Tape measure Assembly holes Drying cabinet back wall Wall behind the drying cabinet 3 4 2. 5. 5 15 7. Fix the two parts of the wooden strip in place using two screws, each of them screwed into the wall behind the drying cabinet, so that they correspond with the holes marked as in point 4. Push back the drying cabinet into its final location. Take off the adhesive tape holding the door and check that the wooden strip is in place on the back wall of the drying cabinet. [. . . ] If a softening agent or antistatic substance is used, the manufacturer's instructions concerning the utilisation of the product should be followed. Remove items from the drying cabinet as soon as they are dry. This reduces the drying time for the remaining damp garments. 20 Setting the temperature selector knob Do not use any heat when drying articles of clothing filled with foam rubber or similar material. 3 1 2 The temperature selector knob regulates heat by means of a continuous scale of temperature positions from no heat at all till normal position with full heat. Setting 1 Type of fabric Foam rubber products, plastic, clothes which are sensitive to heat Sportswear, underwear, shirts, blouses, silk garments, washable knitted products Sturdy working clothes, denim, cotton garments, training sweaters (cotton) Temperature Fan only Low 2 3 Normal 21 Care Cleaning the drying cabinet High-pressure cleaning should not be used! The walls of the cabinet should be cleaned with a mild soap solution on a damp cloth. Dust frequently gathers round the air intake orifice on the upper part of the cabinet. [. . . ]