User manual MC CULLOCH CS380T

[. . . ] Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • Approved protective helmet • Approved hearing protection • Protective goggles or a visor This product is in accordance with applicable EC directives. Noise emission to the environment according to the European Community’s Directive. [. . . ] (21) Push down the red choke control, 4: This inactivates the choke, which is not needed when starting a warm chain saw. However the movement of the start/stop switch will have engaged a high idle, making warm starting easier. Pull the starter handle, 5: Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. (22) CS 450 Elite Start position, 1: The correct choke/start throttle setting for warm starting is obtained by initially moving the choke control by pulling the red control outward - upwards. (23) Decompression valve, 2: Press the valve to reduce the pressure in the cylinder and make starting easier. Once the machine has started the valve will automatically return to its original setting. (23) Air purge (3): Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). The diaphragm need not be completely filled. (23) Push down the red choke control, 5: This inactivates the choke, which is not needed when starting a warm chain saw. However the movement of the start/stop switch will have engaged a high idle, making warm starting easier. Pull the starter handle, 6: Grip the front handle with your left hand. Hold the chain saw on the ground by placing your right foot through the rear handle. (22) Pull the starter handle with your right hand and pull out the starter cord slowly until you feel a resistance (as the starter pawls engage) then pull firmly and rapidly until the engine fires. Note the following before starting: The chain brake must be engaged when the chain saw is started to reduce the chance of contact with the moving chain during starting. Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries. Make sure you have a secure footing and that the chain cannot touch anything. Starting The chain brake must be engaged when the chain saw is started. Activate the brake by moving the front hand guard forwards. (20) Cold engine CS 410 Elite Start position, 1: Set the start/stop switch in the choke position by pulling the red control outward - upward. (21) Air purge, 2: Press the air purge diaphragm repeatedly until fuel fills the diaphragm (at least 6 times). [. . . ] Power, m/sec 13/33 13-18/33-45 12-17/31-43 0, 325/8, 3 0, 050/1, 3 Spur/7 17, 3 13/33 13-18/33-45 12-17/31-43 0, 325/8, 3 0, 050/1, 3 Spur/7 17, 3 2, 0 2, 5 2, 4 2, 9 104 113 115 114 116 4, 7 5, 3 0, 35 13 0, 24 Automatic 0, 46 13 0, 30 Automatic NGK BPMR 7A/ Champion RCJ 7Y 0, 5 NGK BPMR 7A/ Champion RCJ 7Y 0, 5 40, 9 41 31 2900 1, 6/9000 45, 7 42 33 2700 2, 0/9000 CS 450 Elite Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/ EC. Note 2: Equivalent sound pressure level, according to ISO 22868, is calculated as the time-weighted energy total for different sound pressure levels under various working conditions. Typical statistical dispersion for equivalent sound pressure level is a standard deviation of 1 dB (A). Note 3: Equivalent vibration level, according to ISO 22867, is calculated as the time-weighted energy total for vibration levels under various working conditions. [. . . ]