User manual MCCULLOCH PROMAC 61 DEKO

[. . . ] PRO MAC 54 54 CC PRO MAC 61 59 CC GR TMHMANTIKETM ¶HPOºOPIETM ¢È·, ¿ÛÙ ÙÔ ÚÈv ·fi ÙË ¯Ú<ÛË Î·È ÊÏ¿ÍÙ ÙÔ ÁÈ· v· ÙÔ ÛÌ, ÔÏÂÂÛÙ ÛÙÔ Ì¤ÏÏÔv A. B. C. D. Partner oil 50 : 1 McCulloch oil 40 : 1 2T oil 25 : 1 1 ltr. 4 5 10 20 2% 20 cm3 80 100 200 400 2, 5% 25 cm3 100 125 250 500 4% 40 cm3 160 200 400 800 E. F. G. H. I. L. PRO MAC 54 18"/45cm 68T 3/8" PRO MAC 61 225735B 225739B 86826B (7/32") 225736B 225740B 86826B (7/32") 225737B 225740B 86826B (7/32") 225735B 225739B 86826B (7/32") 225736B 225740B 86826B (7/32") 20"/50cm 72T 3/8" 20"/50cmSP 72T 3/8" g Due to a constant product improvement programme, the factory reserves the right to modify technical details mentioned in this manual without prior notice. i La casa produttrice si riserva la possibilità di variare caratteristiche e dati del presente manuale in qualunque momento e senza preavviso. f La Maison se réserve la possibilité de changer des caractéristiques et des données de ce manuel à n'importe quel moment et sans préavis. [. . . ] ­ Study the direction of the fall of the tree and then plan your exit path away from the planned direction of fall. ­ Don't fell trees when there is a strong wind. 1 Clear the tree base of interfering limbs and brush. Clean the work area from stones or other objects which could damage the chain. If the tree has large protruding roots, remove them before felling (see illustrations). 2 A) Cut a felling notch (A) of 45°on the side you want the tree to fall to a depth of about one third of the trunk diameter (d). Then make a felling cut (B) about 5 cm higher than the felling notch on the opposite side of the tree. Make sure that the felling cut does not go right through the trunk. A hinge (C) must always be left to provide control over the direction of the fall. 3 STARTING AND STOPPING E IMPORTANT. Never start or operate unless bar and chain are properly installed. Before starting always move the saw away from the fuelling area and place it on firm, flat surface, the guide bar to the front. STARTING COLD ENGINE Check that the chain brake is in the disengaged position moving the lever (L) backwards (towards the front handle). Move the stop/run lever (A) up to the cold start position (choke closed |­­ |) When in the cold start position, this lever · also partially opens the throttle. Activate the decompression pressing the valve (D). UK B) Use wedges to control the moment and direction of the fall. 3 When the tree starts to fall, walk away along your preplanned escape path. CUTTING FALLEN TRUNKS 4 A) Limbing thick branches. For limbing and bucking leave the lower limbs to support the log off the ground. Begin with a bottom cut made by the upper side of the bar (A); the depth of the cut should be about one third of the log diameter. Finnish with a top cut (B) meeting the first one. With this technique splitting, cracking can be avoided C) Supported at both ends. Begin with a top cut about one third of the log diameter. [. . . ] I enlighet med EGs Maskindirektiv (89/392/EEC, modifierat i 91/368/EEC), 93/68/CEE (CE märkningsdirektiv) & 89/336/CEE (Elektromagnetisk kompatibilitet). Undertecknad Pino Todero, auktoriserad av E. O. P. I. , intygar att bensindrivna kedjesågar: MS55 - MS60 med 45/50 cm långt svärd, vars serienummer visas ovan, tillverkade av E. O. P. I. , Via Como 72, 23868 Valmadrera (LC), Italia, överenstämmer med den maskin som var föremål för EG-provning i enlighet med Annex VI av Maskindirektivet. EG-provet utfördes av Marchio di Qualità (IMQ), Via Quintiliano 43, 20138 Milano (Italia), EG-provets certifikatsnummer IMQ AT096 DM, IMQ AT097 DM. Denna provningsmetod fastställer att maskìnen överenstämmer med de väsentliga hälso- och säkerhetsföreskrifterna i EGs Maskindirektiv. [. . . ]