User manual MCCULLOCH SUPREME 300B, 30CC

[. . . ] A 3 5 8 20 11 11 8 20 18 12 10 14 D 9 16 15 3 1 13 4 2 Strokes Engine totally sintetyc oil or Partner oil McCulloch oil 50:1 40:1 17 1 ltr 5 10 15 20 2% 20 cm3 100 200 300 400 1 ltr 4 5 10 20 2, 5% 25 cm3 100 125 250 500 2 7 19 23 22 6 21 E1 H F I E2 H L MAX 8T I F A G 24 B1 B2 B3 G A C B L E D B4 B5 B6 F1 A B F2 F3 A B C D E F G H Electrolux Outdoor Products Via Como 72 23868 Valmadrera (Lecco) ITALIA Phone +39 0341 203111 - Fax +39 0341 581671 Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice. Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and trademarks in several countries. © Electrolux Outdoor Products Italy C D B7 B8 B9 F4 F5 The Electrolux Group. 1 choice The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use. [. . . ] · Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and reach a fire, candle, burner or furnace pilot light, water heater, dryer, etc. · The fumes produced by the fuel can cause an explosion or fire. · Never store excessive quantities of fuel. E. Assembly of safety guard Fit the safety guard (A) against the gearbox (I) position the lower clamp (G) in the housing under the shield and the upper clamp (F) over the shaft. Safety guard extension (exclusively for use with nylon string head) · The extension (B) should be installed only for use with the nylon string head, with the aid of the string cutter blade (L), that regulates the length of the string and thus the cutting diameter. · For correct assembly see the illustration on the cover and perform the following sequence of steps: · Insert the extension (B) on the safety guard (A) at the reference notches (C), and fasten with the screws (D), then apply the string cutter blade (L) with the cutting edge facing towards the outside of the shield, and fasten it with the screw (E) (Make sure the screws are tightened all the way (E) and are not loosened by the vibrations. If you are using the grass cutting blade, remove the extension (B) on the guard (A). F. Usable cutting tools and their installation on the machine CAUTION!The following are the only cutting devices that can be installed on your machine: a) Nylon string head b) Grass blade with a maximum of 8 teeth. Each of these devices requires the installation of a special guard. Follow the instructions for correct assembly carefully. Fasten the cutting tools correctly with all their parts in the order indicated so as to prevent severe injuries to the operators, other people and animals. Use grass blades or nylon string heads with the MAXIMUM ROTATION SPEED (stenciled on them by the manufacturer) of at least 10. 500 min-1. Any operations involving the cutting devices and their guards should be done with the engine off. If you turn the machine over to facilitate assembly of the cutting tools, make sure the cap on the fuel tank is securely fastened and there are no leaks of fuel. 6 - ENGLISH CAUTION!WE RECOMMEND THE USE OF ORIGINAL ACCESSORIES AND REPLACEMENTS, WHICH CAN BE PURCHASED FROM AUTHORIZED DISTRIBUTORS. THE USE OF OTHER ACCESSORIES AND REPLACEMENTS INCREASES THE DANGER OF ACCIDENTS AND IN THIS CASE THE MANUFACTURER HAS NO LIABILITY FOR DAMAGES TO PERSONS AND/OR PROPERTY. Assembly of nylon string head and blade Apply the proper guard depending on whether you plan to use the grass blade or nylon string head (see chapter: "Application of protective devices on cutter"). Apply the nylon string head as shown in the illustration: a) Protection flange b) Upper plate c) Guard d) Nylon string head. As you tighten, hold the nylon string head and plate still and insert the wrench or screwdriver supplied in the holes in the plate and gearbox; first turn the plate until the two holes match. Apply the blade as shown in the illustration: a) Protection flange b) Upper plate with blade centering c) Guard d) Blade with wording and direction arrow facing upward e) Lower plate f) Fixed cup g) Blade fastening nut. Do not use the nylon string head guard extension (H) with metal blades. · F4. [. . . ] This will prevent the blade from touching the ground. N1. WE RECOMMEND THE USE OF ORIGINAL ACCESSORIES AND REPLACEMENTS; THESE CAN BE FOUND AT YOUR OFFICIAL DISTRIBUTOR'S. THE USE OF ACCESSORIES AND REPLACEMENTS THAT ARE NOT ORIGINAL INCREASES THE DANGER OF ACCIDENTS AND IN THIS CASE THE MANUFACTURER IS NOT LIABLE FOR ANY DAMAGES TO PERSONS OR PROPERTY. O. Environmental information This section contains information useful for maintaining the characteristics of ecocompatibility included in the origin design of the machine, and as regards proper use and disposal of oil and fuel. [. . . ]