User manual MCINTOSH C11 SERVICE MANUAL

[. . . ] Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. [. . . ] Default Settings Function Name McIntosh C11 SOURCE INPUT (connector type) LEVEL (Trim) DISPLAY (Brightness) PASSTHRU TRIG 1 Output (Action) TRIG 2 Output (Action) COMM PORT (Baud Rate) REMOTE (Codes) Setting V_. _ _ - _. _ RCA 0. 0dB 3 OFF MAIN MAIN 115200 NORM Page No. 13 13 14 15 15 16 16 17 17 Source Inputs Reassignment The C11 provides the ability to reassign the nonPhono Inputs (High Level) to either one of two Balanced Inputs or one of the four Digital Inputs. In the first example, the CD2 Input will be reassigned from the unbalanced CD2 (RCA Jacks) to the BALANCED 1 (XRL Connector). SOURCE: TUNER 15% Figure 1 2. Press and hold the EQ BYPASS/SETUP Pushbutton until the Front Panel Information Display indicates "McIntosh C11, V1. 00 - 1. 0 "or higher Firmware. At this time the LED McIntosh C11 V1. 00 - 1. 0 Figure 2 above the TRIM Push-button will be illuminated. Press the OUTPUT 2 / MENU Push-button to select the next Setup Mode Menu item, "SETUP: SORCE INPUT, TUNER : RCA". With each additional press of the OUTPUT 2 / MENU Notes: 1. Any one of the Default Inputs may be swiched Off. If any input is switched Off its name will no longer appear on the Front Panel Information Display when using the INPUT Control, nor is it accessible with the Remote Control. The Phono MC (Moving Coil) and MM (Moving Magnet) Input are designed for connection of a turntable only and thus non-reassignable. However, the Phono Inputs may be switched Off. Refer to figure 7. LEVEL: CD Min || Figure 9 0. 0dB Max SETUP: SOURCE INPUT SRVR : RCA Figure 7 Note: The CD Input is serving as a reference level or choose another source frequently listened to. The Input Source should be set to a reference Level (Trim) of 0. 0dB. 14 Setup, con't Display Brightness 3. Rotate the INPUT Control until "LEVEL: SRVR 0. 0dB" appears on the Front Panel Information Display. If necessary, rotate the VOLUME/ADJUST Control to obtain the same volume level as the CD Input by switching between the two Inputs using the INPUT Control. Rotate the INPUT Control until "LEVEL: SRVR _. _" appears on the Front Panel Information Display. The illustration in figure 10 indicates a The Front Panel Information Display Brightness may be changed from the default setting. The C11 will remember two brightness preferences, one with the Meters Illuminated and one without Meter Illumination. For each preference there are four brightness settings for the Information Display. The Display Brightness setting may be varied 1 (Dim) to 4 (Bright). Follow the steps below for reducing the Display Brightness (with the Meter Illumination On). Press and hold the EQ BYPASS/SETUP Pushbutton until the Setup Mode is active. [. . . ] The illustration to the right shows the fundamental frequency range of acoustical musical instruments and the human voice. It also shows the range of adjustment of frequencies for each of the Equalizer Controls of the C11 at the +6dB and -6dB points. Passthru When the C11 is connected together with a McIntosh Multichannel A/V Control Center or Surround Decoder and has the PASSTHRU MODE activated, it will automatically turn-on when the A/V Control Center or Surround Decoder is turned On. It will indicate on the Front Panel Alphanumeric Display "PASSTHRU". [. . . ]