User manual MCINTOSH MCC406M

[. . . ] Power Amplifier MCC406M Owner's Manual McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. To prevent the risk of electric shock, do not remove cover or back. No user serviceable parts inside. IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. 1. Install in accordance with the manufacturer's instructions. [. . . ] Connect cables (up to 12 AWG) from four separate Loudspeaker Systems to the MCC406M Power Amplifier Channels 1, 2, 3, and 4 being careful to observe the correct polarities. Connect cables (up to 12 AWG) from the Subwoofer Loudspeaker Drivers to the MCC406M Power Ampli- fier Channels 5 and 6 BRIDGED connection being careful to observe the correct polarities. Connect audio cables from the McIntosh Control Center Front and Rear Outputs to the MCC406M Power Amplifier Inputs 1, 2, 3, and 4. Connect the optional McIntosh external Subwoofer Remote Volume Control to the SUB REMOTE CONTROL Jack on the right side of the MCC406M Power Amplifier. Connect the MCC406M to the vehicle battery terminals using size 4 AWG (Maximum) cables. Note: It is advisable to place an in-line fuse of a suitable size as close as possible to the battery. Left Rear Output Right Rear Output Power Guard Amp ON Left Front Output Right Front Output Left Front Loudspeaker System McIntosh External Subwoofer Rotary Control Right Front Loudspeaker System Left Rear Loudspeaker System (+) Right Rear Loudspeaker System - Vehicle + Battery Fuse (-) Subwoofer 10 How to Connect for Four Channels How to Connect for Four Channels 1. Connect a cable from the Control Center Amp On to the MCC406M ON Connector on the right side of the amplifier. Note: All cables should be connected to the amplifier before connecting the DC power cables to the battery. fier Channels 5 and 6 Outputs being careful to observe the correct polarities. Connect audio cables from the McIntosh Control Center Front and Rear Outputs to the MCC406M Power Amplifier Inputs 1, 2, 3 and 4. Note: The Subwoofer Output Level can be remotely controlled by the optional McIntosh External Subwoofer Rotary Control connected to the SUB REMOTE CONTROL jack on the MCC406M. 2. Connect a cable from a McIntosh Control Center with Power Guard to the MCC406M PG Connector on the right side of the amplifier. Connect cables (up to 12 AWG) from two separate Loudspeaker Systems to the MCC406M Power Amplifier Channels 1 and 2 BRIDGED; 3, and 4 BRIDGED connections being careful to observe the correct polarities. Connect cables (up to 12 AWG) from the Subwoofer Loudspeaker Drivers to the MCC406M Power Ampli- 6. Connect the MCC406M to the vehicle battery terminals using size 4 AWG (Maximum) cables. Note: It is advisable to place an in-line fuse of a suitable size as close as possible to the battery. Left Rear Output (Subwoofer Level) Right Rear Output Optional connections for controlling the Subwoofer Level by using the Front to Rear Fader Control on the Control Center Subwoofer (+) Power Guard Amp ON Left Front Output Optional McIntosh External Subwoofer Rotary Control Right Loudspeaker System Right Front Output (-) Left Loudspeaker System (+) - Vehicle + Battery Fuse (-) Subwoofer 11 How to Connect for Three Channels 1. Connect a cable from the Control Center Amp On to the MCC406M ON Connector on the right side of the amplifier. Note: All cables should be connected to the amplifier before connecting the DC power cables to the battery. 2. Connect a cable from a McIntosh Control Center with Power Guard to the MCC406M PG Connector on the right side of the amplifier. Connect cables (up to 12 AWG) from a Loudspeaker System to the MCC406M Power Amplifier Channels 1 and 2 BRIDGED connections. In a similar manner connect another Loudspeaker system to the 3 and 4 BRIDGED connections, being careful to observe the correct polarities for all connections. 4. Connect cables (up to 12 AWG) from the Subwoofer Loudspeaker Drivers to the MCC406M Power Amplifier Channels 5 and 6 BRIDGED connection being careful to observe the correct polarities. Connect audio cables from the McIntosh Control Center Front Outputs to the McIntosh Custom Environmental Equalizer Inputs 1 and 2. Connect audio cables from the McIntosh Custom Environmental Equalizer Outputs 1 and 2 to the MCC406M Power Amplifier Inputs 1 and 3. Connect the optional McIntosh external Subwoofer Remote Volume Control to the SUB REMOTE CONTROL Jack on the MCC406M Power Amplifier. Connect the MCC406M to the vehicle battery terminals using size 4 AWG (Maximum) cables. Note: It is advisable to place an in-line fuse of a suitable size as close as possible to the battery. (+) Power Guard Amp ON McIntosh External Subwoofer Rotary Control Right Front Output Left Front Output McIntosh Custom Environmental Equalizer - Vehicle + Battery Fuse (-) 12 How to Connect for Three Channels Left Loudspeaker System Right Loudspeaker System Subwoofer 13 Top Panel Controls, Display and Switches CH 5-6 LOW PASS Filter Switch and Control select the high frequency roll-off or flat frequency response CH 5-6 SENSITIVITY Individual Input Sensitivity Controls for Channels 5 and 6 CH 5-6 MODE Switch selects STEREO or BRIDGED mode of operation CH 5-6 HIGH PASS Filter Switch and Control select the low frequency roll-off or flat frequency response POWER GUARD LED lights when the Power Guard Circuit activates for Amplifier Channels 5 or 6 POWER GUARD LED lights when the Power Guard Circuit activates for Amplifier Channels 1 thru 4 INPUT SOURCE Switch for Channels 5-6 selects either CHs 5 and 6, 1 and 2 or Subwoofer (Sum of CHs 1, 2, 3, and 4) METER indicates Channels 1 thru 4 Power Output METER indicates Channels 5 and 6 Power Output CH 1-2 MODE Switch selects STEREO or BRIDGED mode of operation CH 3-4 MODE Switch selects STEREO or BRIDGED mode of operation CH 3-4 HIGH PASS Filter Switch and Control select the low frequency roll-off or flat frequency response INPUT SOURCE Switch for Channels 3-4 selects either CHs 3 and 4 or 1 and 2 CH 1-2 HIGH PASS Filter Switch and Control select the low frequency roll-off or flat frequency response CH 3-4 LOW PASS Filter Switch and Control select the high frequency roll-off or flat frequency response CH 1-4 SENSITIVITY Individual Input Sensitivity Controls for Channels 1, 2, 3 and 4 14 How to Operate the MCC406M Introduction The McIntosh MCC406M is a highly versatile amplifier that can be configured in many ways. This manual gives examples of some of the most common configurations. The best way to set the filter controls is through the use of a real-time spectrum analyzer and the expertise of a professional installer. [. . . ] Temporarily place the removed glass panel in a safe place, remove the suction cup and save it for future use. Remove the Phillips Screws holding the End Caps on both sides of the amplifier and lift the end caps off. Remove the two Phillips screws located between the low and high pass filter controls. Remove all 12 crossover, equalizer and sensitivity knobs. [. . . ]