User manual MCINTOSH MDA5000 D/A CONVERTER

[. . . ] This unit is capable of producing high sound pressure levels. Continued exposure to high sound pressure levels can cause permanent hearing impairment or loss. User caution is advised and ear protection is recommended when playing at high volumes. Disconnect this equipment when unused for long periods of time. [. . . ] 7 How to Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Top Panel Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Packing Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Please Take A Moment The serial number, purchase date and McIntosh dealer name are important to you for possible insurance claim or future service. The spaces below have been provided for you to record that information: General Notes 1. The MDA5000 Digital/Analog Converter Operation is fully Automatic and requires no selection or adjustment on the part of the user. When a CD that has been specially encoded with a High Definition Compatible Digital® Signal is received, the MDA5000 will automatically decode the additional information. For additional connection information, refer to the owner's manual(s) for any component(s) connected to the MDA5000 Digital/Analog Converter. The MDA5000 Digital/Analog Converter is designed to Automatically Switch Power On and Off with the rest of the Audio System. In order for the automatic power switching to function, there needs to be a connection between the Control Center and the Converter. An Automatic Digital Input Selector is built into the MDA5000 . It will accommodate up to three source devices with digital outputs to be connected to the converter. The MDA5000 can only decode one input source at a time. If the MDA5000 receives more than one digital signal simultaneously, the Automatic Digital Input Selector will not function properly. Serial Number: Purchase Date: Dealer Name: Technical Assistance If at any time you have questions about your McIntosh product, contact your McIntosh dealer who is familiar with your McIntosh equipment and any other brands that may be part of your system. If you or your dealer wish additional help concerning a suspected problem, you can receive technical assistance for all McIntosh products at: McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903 Phone: 607-723-1545 Fax: 607-723-3636 Customer Service If it is determined that your McIntosh product is in need of repair, you can return it to your dealer. You can also return it to the McIntosh Laboratory Service Repair department. For assistance on factory repair return procedure, contact the McIntosh Repair Department at: McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903 Phone: 607-723-3515 Fax: 607-723-1917 Copyright 2003 © by McIntosh Laboratory, Inc. , HDCD®, High Definition Compatible Digital® and Pacific Microsonics are either registered trademarks or trademarks of Pacific Microsonics, Inc. in the United States and/or other countries. HDCD System manufactured under license from Pacific Microsonics, Inc. [. . . ] Removing the End Cap To access the MDA5000 Connecting Terminal Block, remove the Glass Panel first (the above step) and then remove the Phillips Screws holding the Left Side End Cap of the Digital/Analog Converter and lift the End Cap off. See figure 2. Remove Top Cover Screws Figure 1 Remove Top Cover Screws Remove End Cap Screw Figure 2 Remove End Cap Screw 6 Side Panel Cooling and Connections AUDIO OUTPUTs Analog Signal Output for connection to a Control Center Connect to the Negative (-) vehicle battery terminal Connect to the positve (+) vehicle battery terminal Receives the Turn-ON Signal from a McIntosh Control Center and sends a Turn-ON Signal on to another component in the Audio System COAXIAL DIGITAL AUDIO INPUTs for cables from a CD Signal Source Digital Output OPTICAL DIGITAL AUDIO INPUT for a cable from a CD Signal Source Digital Optical Output 7 How to Connect How to Connect The McIntosh MDA5000 is intended to be utilized in an Audio System that can support a separate outboard Digital to Analog Converter. Connect a wire from the Control Center Amp On to either MDA5000 ON Connectors on the left side of the Digital to Analog Converter. Note: All cables should be connected to the Digital to Analog Converter before connecting the DC power cables to the battery. The second ON Connector provides the Power On Signal for another component in the Audio System. 2. [. . . ]