User manual MCINTOSH MX136 AUDIO AND VIDEO PREAMPLIFIER/PROCESSOR

[. . . ] A/V Control Center MX136 Owner's Manual Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic" and the double-D symbol are trademarks of Dolby Laboratories. Patent No's: 5, 451, 942; 5, 956, 674; 5, 974, 380; 5, 978, 762; 6, 226, 616; 6, 487, 535 & other U. S. and worldwide patents issued & pending. [. . . ] As the test signal switches to succeeding Loudspeakers, 3. Determine whether you wish to use the Automatic (requires less push-button presses) or Manual (quicker when used with a sound pressure meter) Loudspeaker Level switching mode. For Automatic switching, proceed to Step 4. For Manual switching, proceed to Step 11 on the next page. Automatic Loudspeaker Level Switching 4. Using the Left or Right directional push-buttons, select AUTO MODE from the SPEAKER LEVEL OnScreen Menu, followed by pressing the SELECT/OK Push-button to activate the Automatic Loudspeaker Level Switching Mode. The test signal will start cycling continuously through all Loudspeakers in 2-second intervals. While in the Listening/Viewing area, note the volume levels from each of the Loudspeakers as the test signal switches. If you determine that the test signal volume is MENU: SPEAKER LEVEL AUTO MODE: PRESS SELECT LEFT FRONT 0 CENTER 0 RIGHT FRONT 0 RIGHT SURROUND 0 RIGHT BACK SURR 0 LEFT BACK SURR 0 LEFT SURROUND 0 SUBWOOFER 0 MAIN MENU Figure 12 31 MENU: SPEAKER LEVEL AUTO MODE: SELECT TO STOP LEFT FRONT 0 CENTER 0 RIGHT FRONT 0 RIGHT SURROUND 0 RIGHT BACK SURR 0 LEFT BACK SURR 0 LEFT SURROUND 0 SUBWOOFER 0 MAIN MENU MENU: SPEAKER LEVEL MANUAL MODE: PRESS SELECT LEFT FRONT 0 CENTER 0 RIGHT FRONT 0 RIGHT SURROUND 0 RIGHT BACK SURR 0 LEFT BACK SURR 0 LEFT SURROUND 0 SUBWOOFER 0 MAIN MENU Figure 13 Figure 14 repeat the level adjustment process until the test signal volume levels of all the Loudspeakers are the same. The Loudspeaker level cycling mode can be repeated as often as necessary. Press the SELECT/OK Push-button to switch Off the Automatic Loudspeaker Level Switching Mode. If you do not wish to perform INPUT SETUP Adjustments at this time, select MAIN MENU from the menu. The MAIN SYSTEM SETUP Menu will reappear on the Monitor/TV screen and proceed to the next step. Select EXIT from the MAIN SYSTEM SETUP Menu. If you are satisfied with the changes that you may have made, select YES to save those changes or NO not to save them. The MX136 will then return to normal operation. Using the Left or Right directional push-buttons, select MANUAL MODE from the SPEAKER LEVEL On-Screen Menu, followed by pressing the SELECT/ OK Push-button to activate the Manual Loudspeaker LEVEL Switching Mode. Adjust the volume of the Loudspeaker by pressing the Left or Right directional push-buttons on the Remote Control. Using the Up or Down directional push-buttons, select the next Loudspeaker and perform the level adjusting procedure. Continue this for each of the remain32 ing Loudspeakers. Repeat this as often as necessary until you are satisfied that the volume levels of all the Loudspeakers are the same. Press the SELECT/OK Push-button to switch Off the Manual Loudspeaker Level Switching Mode. [. . . ] Refer to figure 66. Note: Presets are automatically assigned in order from 1 to 9 unless a different Preset Number is selected. Figure 68 4. To clear any additional Station Presets perform steps 1 through 3 again. Figure 66 4. Press and release the Front Panel ENTER Push-button a second time to store the Preset into memory. The just entered Station Preset Selection will be assigned Preset Number 1 which is displayed on the far right side of the Front Panel Alphanumeric. [. . . ]