User manual MEDION BDAPC8810PT

[. . . ] 18 Connecting the transmitter to a computer . 23 Connecting via a DIN AV cinch cable . 29 3 81241 TEVION UK. book Seite 4 Mittwoch, 23. August 2006 1:47 13 SAFETY INSTRUCTIONS Please read these instructions carefully before using the system and note the warnings in the operating instructions. [. . . ] The three infrared transmitters in the infrared extender then send these signals on to the relevant devices. Scart or Cinch If the audio/video source has a SCART connection, use the SCART adapter for the transmitter. If the device connected to the receiver has a SCART connection use the SCART adapter for the receiver. If the device connected to the receiver does not have a SCART connection, use the DIN-AV cinch cable or a 75 Ohm aerial cable. If the audio/video source has a 3. 5mm audio output use the audio adapter supplied. 9 81241 TEVION UK. book Seite 10 Mittwoch, 23. August 2006 1:47 13 Range Audio and video signals are transmitted in the 2. 4GHz range. The range may be less depending on environmental conditions. Example use 10 81241 TEVION UK. book Seite 11 Mittwoch, 23. August 2006 1:47 13 SCOPE OF DELIVERY Remove all packing materials. When unpacking, ensure that the following parts are included: · Transmitter · 1x mains adapter for the transmitter 6 V 300 mA · Receiver · 1x mains adapter for the receiver 6 V 300 mA Cables supplied · 1 infrared extender with three external IR transmitters · 1x SCART adapter for the transmitter · 1x SCART adapter for the receiver · 1x DIN SCART cable for the A/V input "source device 1" · 1x DIN SCART cable for the A/V output "TV" 11 81241 TEVION UK. book Seite 12 Mittwoch, 23. August 2006 1:47 13 · 1x audio adapter 3. 5mm stereo jack to cinch socket · 1x AV cinch cable · 1x DIN AV cinch cable Packaging The radio transmission system is packaged to protect it against transportation damage. August 2006 1:47 13 Connecting the mains adapter · Connect the mains adapter to the 6V socket (DC 6 V) on the transmitter. · Remove the protective cover and insert the mains adapter into the socket (230V ~ 50Hz). · Set the ON/OFF switch to the ON position. · Open up the transmitter aerial and align it with the receiver. Selecting a channel · Use the channel switch at the bottom of the device to select a channel (A/B/C/D) to which the signal is to be sent. 18 81241 TEVION UK. book Seite 19 Mittwoch, 23. August 2006 1:47 13 CONNECTING A COMPUTER THE TRANSMITTER TO You can also connect the transmitter to a computer in order to transmit computer output to a television, for example. It does not usually make sense to transmit computer output to a TV for running computer applications, since the TV's screen display is not usually good enough to display the higher resolution computer image. If you want to show videos or presentations, however, displaying them via the TV is highly recommended. The following requirements have to be fulfilled: · Your computer has a video output that provides video images suitable for a TV. · The operating system and the drivers for your graphics card support video output. How to proceed Output via video output is activated differently depending on your operating system and graphics card. As there are numerous combinations of these, we can only provide general instructions here. Please check the operating instructions for your computer or graphics card to see how you can divert the image to video output. The following example requires a PC running the Windows® 98 operating system or above. · Close all programs and switch off your computer. [. . . ] August 2006 1:47 13 SETTING CHANNELS Your radio transmission system has four channels ­ i. e. , four different frequencies can be used. The channel switch is on the bottom of both devices. · Set the transmitter and receiver to the same channels. · Test which channel (A/B/C or D) provides the best reception. [. . . ]