User manual MEDION DIGITAL NOTEPAD MD 85276

[. . . ] Contents: Safety and service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operating safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Point of use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Environment condidtions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You could damage the digital writing block by inserting the batteries incorrectly. Close the battery compartment again by repositioning the cover and pushing it back to the starting position carefully. We recommend the use of alkali batteries for practical application. Operation with NiMH batteries is also possible. Bringing the device into operation 11 New batteries will have a writing period of about 20 hours. However, the actual time will heavily depend on the brand and the quality of the batteries used. Digital pen: If the LED [13] starts to flash or the lines are no longer correctly displayed, the batteries of the digital pen are almost empty. Please replace the batteries in that case. It will be activated automatically if it comes into the proximity of the entry surface and will switch off when it leaves this area. Open the battery compartment by unscrewing the digital pen. Remove the used battery and insert a new AAA battery in accordance with the following illustration, if necessary: + 3. Screw the digital pen back together. - Note: Read the notes from Page 5 for dealing with batteries safely. 12 Bringing the device into operation Inserting paper Paper clamp Note: The stack or block of paper must not exceed a height of 13mm (~135 sheets), because the movements of the pen will not be recognized correctly otherwise. The applicable writing area has dimensions of 216mm x 280mm (8. 5" x 11" = letter format). Press the paper clamp and introduce the paper flush to the edges. Release the paper clamp, in order to stabilize the paper. . Attaching the digital pen You can keep the digital pen in this way when it is not being used: There is an indentation on the left in the paper clamp, at which you can attach the pen cap. Bringing the device into operation 13 Installation of software Content of the disc "Software": - USB Pen Pad Driver : Necessary for installing the drivers of the device - MyInk Suite : Software for administering projects - Power Presenter RE : Program to assist working on source files - Free Notes & Office Ink : Program for administering and converting - Pen Soft : Program to assist the Taskbar with extended functions Content of the disc "MyScript Notes" : Main program for script recognition. Important: You should install the necessary software (drivers and image processing) first, before you connect the A4 Size Digital Notepad. Your important files can be changed or deleted during the installation of software. Make sure that you back up your hard disk, to avoid problems when using older files after any installation. Insert the supplied disc labelled "Software" to start the installation automatically. Note: If installation does not start automatically, please proceed as follows: 1) Open the "Start" menu and select "Run". 2) Then enter the letter for the CD-ROM drive followed by a colon and the name of the program: "Setup". Afterwards you are free to choose all application and tools that you would like to use. [. . . ] The Pen symbol does not appear in the LCD display. Check the energy status of the batteries. Make sure that you are writing in the recognizable area. Restart the device or carry out a Reset (press the Reset button [7] on the back of the device). [. . . ]