User manual MEDION MD 86162 QUICK GUIDE

[. . . ] Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Information about these Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Use in accordance with regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Fades out when the device is switched off. Shines red in the stand-by mode; flashes when the system is booting or shutting down; shines blue when the device is switched on; flashes blue if the remote is being used. Remote sensor: Point the remote to this point. 11 Back of the device 5. Remove the battery from the remote if the device will not be used for a longer period. The remote could be damaged by a 15 leaking battery. 16 Connecting the device HDMI connection Connect the HDMI cable to the HDMI socket of the device and to the corresponding input socket on the television device. The (PAL, 480P, 576P, 720P (50Hz), 720P (60Hz), 1080i (50Hz), 1080i (60Hz), 1080P (50Hz), 1080P (60Hz) or NTSC resolution can be set for HDMI output by pressing the INFO button several times (only in the HOME Menu) during an HDMI connection. Notes about HDMI connection Set the [AUDIO] option, [DIGITAL OUPUT] sub-menu, to [HDMI LPCM] (see Page 35) in the Settings Menu, if your television has no Dolby Digital or MPEG decoder. Pay attention to the following points when connecting an HDMIcompatible device: - Switch off the HDMI device and the Media Player. Now, switch on the HDMI device, wait approx. 30 seconds, and then switch on the Media Player. 17 - The video input of the connected device must have been set to the Media Player. - The connected device must support one of the PAL, 480P, 576P, 720P (50Hz), 720P (60Hz), 1080i (50Hz), 1080i (60Hz), 1080P (50Hz), 1080P (60Hz) or NTSC video input resolutions. Connection to the AV sockets Connect the AV jacks of the Media Player to the audio/video input sockets of the TV device by means of the audio/video cable supplied. Only PAL and NTSC resolutions are supported through this output; use the HDMI output if you want to enjoy HD content. 18 Connecting to the outputs of components Connect the Y Pb Pr jacks of the device to the corresponding input sockets of the TV device by means of the video cable supplied. Note: Only the picture will be output through the outputs of the component. The analog or digital connections of the Design Full-HD Media Player must be connected to the TV device or an audio device in addition, for the transmission of the sound signal. 19 Optical digital connection Connect the SPDIF jack of the device to the corresponding socket on the digital audio device (e. g. an A/V amplifier) by means of an optical cable, for the transmission of digital audio signals. Connecting a data medium by means of USB Connect a USB hard drive to the USB socket on the front or the back of the device by means of a USB cable. You can also plug in a USB stick at one of the sockets. 20 Network connection Connect the RJ45 socket on the device to a network interface (e. g. a router), by means of a cable with the corresponding jacks. The Design Full-HD Media Player will be able to access released files in the network in this way. Connection for memory cards Plug a memory card (Type SD/SDHC/MMC/MS/MSPro) into the socket on the front of the device, in order to be able replay the files on the memory card. Note: The Design Full-HD Media Player supports SD, SDHC and MMC memory cards and MS and MSPro type memory sticks. 21 Connecting the power pack Connect the power supply plug of the adapter (KSAD1200150W1EU 12V DC 1. 5A) supplied to the DC socket on the device. Connect the mains adapter to a socket (AC 230 V ~ 50 Hz) when you have made all the connections. Take the details of the mains adapter from the Technical Data on Page 53. 22 Bringing the device into operation for the first time An overview, in which you can make the following settings, will appear after connection to the power supply, when you put the device into operation for the first time; Menu language Set the Menu language here, as described on Page 38. Time Set the time and date here, as described on Page 39. Setting up LAN Set the network configuration here, as described on Page 37, if you want to connect a network cable. 23 Operation Switching the device on and off The ON/OFF switch will initially flash blue, in order to signal that the system is booting, if you have connected the device with the electricity network through the mains adapter. After this, it will shine blue continuously and the device will be ready to operate. Press the Standby/ON button on the remote, to switch the device to the Stand-by mode. The ON/OFF button shines red in the Stand-by mode. Press the Standby/ON button on the remote or the ON/OFF button on the device again, to switch the device out of the Stand-by mode. [. . . ] What messages have appeared on the screen? During which operating step has the problem arisen? If you have connected a PC to the device: ­ What is your computer configuration?­ What software were you using when the error arose? [. . . ]