User manual MERIDIAN AUDIO G01 02

[. . . ] G Series Control Unit and Receiver Installation Guide ii Preface Important safety instructions · Read the instructions. · Do not use this apparatus near water. · Install only in accordance with the manufacturer's instructions. · Refer all servicing to approved service personnel. [. . . ] Alternatively you can program it to be high for specific sources; eg to control a projection screen. 14 Installing the control unit or receiver To connect to other Meridian G Series, 500 Series, or 800 Series equipment G01/G02/G51 G Series, 500 Series, or 800 Series unit COMMS COMMS COMMS LEAD COMMS LEAD In a system of Meridian products, one of the products acts as the controller for the system, receiving infra-red commands from the MSR+, and then, if appropriate, relaying them to the other products via the Comms link. The following procedure should be used to set up the Comms correctly between several products: · Connect one of the DIN COMMS sockets on the back panel of the control unit or receiver to one of the COMMS sockets on another G Series, 500 Series, or 800 Series unit, using the Comms leads provided with the products. One unit will then be designated as the controller, and display: Con. All the other units will be configured as non-controllers, and display: Not Con. The sytem is now ready for use. The sequence in which you connect the units is not important. If the automatic setup does not work, first make sure you are · Switch all the units to standby. Each unit will display: operating the MSR+ from a position where all the units can receive the infra-red, and try again. Then: · Check that none of the units have been configured to be IR Controller; see Other settings, page 22. Either all products should be set to Auto, or one should be configured as Controller and the others as Not Controller. Auto 15 Installing the control unit or receiver Note: Do not, under any circumstances, connect any equipment other than Meridian G Series, 500 Series, or 800 Series to any socket marked COMMS on the back of the product. To connect FM and AM antennae (G01 and G51 only) · Connect an FM antenna or split-flex dipole to the FM Coax connector, if necessary using the adaptor provided. In the UK use a female Belling-Lee (VCR) connector. The product is supplied with an indoor loop antenna. This is directional, and for best results you will need to orient it, and this may be station dependent. · Place the antenna as far away from other electrical equipment Although the FM tuner is very sensitive, the FM antenna is supplied for basic installation only, and for best performance and lowest noise use a high-quality antenna placed as high as possible and oriented towards the transmitter. and as high as possible. For best AM results use an external AM antenna. Note: For AM you must fit a good ground as well as an antenna. Note: For all outdoor antennae we strongly recommend you use a qualified installer who will comply with local safety regulations. · Connect an AM antenna to the AM connector by pressing the tabs and inserting a bare wire into each hole. The ground connection (black on the supplied AM antenna) should be connected to the socket marked GND. The tuner can be used with most proprietary indoor AM, FM, or combi (AM/FM) antennae. It is possible in some cases to use a trigger output from the product to power such devices. For more details, look at the Library/Applications sections of the Meridian web site at www. meridian-audio. com/lib-apps. htm. 16 Installing the control unit or receiver 17 Configuring the control unit or receiver Configuring the control unit or receiver This chapter explains how to configure the control unit or receiver using the Configuration Wizard. Alternatively, for complete control over all aspects of the product's configuration you can set up the unit from a computer using the Meridian Configuration Program. For full information refer to the Meridian Configuration Program Guide available separately. Configuration Wizard The Configuration Wizard leads you through the correct sequence to configure your control unit or receiver. Alternatively, you can skip between the configuration stages, which allow you to reset the configuration, or configure the sources or other settings of the control unit or receiver. To run the Configuration Wizard · If necessary press On/Off to put the control unit or receiver into standby. If the product is locked the display shows: The displays then shows: Version Wizard Lock · Press Wizard. [. . . ] Do not use any other solvent or abrasive based cleaners. Dust can be removed from the disc drive tray with a small dry brush when the drawer is open. Ensure that no liquid enters the casework and that the product is completely dry before re-connection. To clean the audio connections The audio sockets on the back of the product are gold plated and do not need to be cleaned if gold-plated plugs are used. [. . . ]