User manual METO-FER LH 300

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual METO-FER LH 300. We hope that this METO-FER LH 300 user guide will be useful to you.

Lastmanuals help download the user guide METO-FER LH 300.


Mode d'emploi METO-FER LH 300
Download
Manual abstract: user guide METO-FER LH 300

Detailed instructions for use are in the User's Guide.

[. . . ] This linear movement can be adjusted in its working area (stroke). Safety Precautions Before starting to operate the linear unit LH, it is necessary to check that no body parts are within the working range of the element. In such a case the unit must not be operated. [. . . ] 4. 1 INITIAL OPERATION Compressed Air Remove the safety caps from the air connections. In order to regulate the velocity of the movement, we recommend our one-way restrictors DV-R1/8" (see sheet 5. 021). Unused air connections must be covered with the R1/8 caps. 4. 2 Stroke Adjustment Loosen screw (Pos. 102 and 110) and plate (Pos. 9), move to the needed position. Tighten screw, make sure piston rod and shaft (Pos. 6) are parallel. Adjust the needed stroke on AS 12/60 (Pos. 115). Tighten security nut on the stop screw. 4. 3 Cushion Adjustment The basic adjustment of the cushions has to be optimized by the user upon his special requirements. The position of the cushions can be seen on the construction drawing. The brake resistance can be changed by adjusting the length of the brake path. When using oil and elastomer cushions, it must be checked that the end stop is not made by the cushions. The cushions should show a remainder stroke of 0. 039" (1mm). 5. 5. 1 MAINTENANCE Introduction 5 The linear unit does not require any special maintenance procedure. Never use any type of solvents in order to clean the unit. OPERATING MANUAL (LH) 5. 2 Air Supply The linear unit is equipped with oil-free seals and can be operated with dry and non-oiled compressed air. If oiled compressed air is used, we recommend: Airpress compound SAE 5 (Klueber Order No. 6. 1 REPAIR Introduction If the unit no longer meets the requirements (leakage, wear, etc. ) the defective parts must be replaced. 6. 2 Safety Precautions Before dismounting the unit, it is necessary to check that the compressed air supply is interrupted. It is best to disconnect the compressed air supply from the unit. [. . . ] 7. 1 SPARE PARTS LIST Spare Parts When ordering spare parts, the type and serial number of the unit must be stated. Position *109 *111 *112 *113 114 *117 Seal Kit Repair Kit 7. 2 Lubrication Grease for seals Staburag NBU 4 Atemp. Part Number 015. 130. 0100 025. 100. 0680 025. 140. 0055 025. 150. 0810 045. 100. 0007 025. 100. 0410 Description Clips O-Rings Rod Seals Piston Seals Linear Ball Bushings O-Ring Quantity 2 Pieces 2 Pieces 2 Pieces 2 Pieces 4 Pieces 1 Stk. Order No. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE METO-FER LH 300

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual METO-FER LH 300 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag