User manual METRONIC TOUCHBOX 3

[. . . ] Digital Satellite Receiver Ref : 441327-3 2500 channels Parental lock 2 scarts Wide screen ready DiSEqC 1. 2 MET624 CAUTION Your receiver has ventilation slots. These slots must not be obstructed, even partially, in order to ensure proper ventilation. The lifetime of your device depends on these factors. The device may not be exposed to dripping or splashing and no object filled with liquid, such as vases, must be put on the device. [. . . ] Check in the list of the pre programmed channels at the end of the user manual. You can select and watch the channel of this satellite. 23 6 - Connection on a dual-head system Astra + Hotbird already aligned Connect the cables and the leads as indicated on the figure below (figure n°4). It is useful to know on which inputs of the switch the heads Astra and Hotbird are connected. If you do not know it and the installation is difficult to reach, test the 2 possible combinations: Astra on A and HotBird on B or Astra on B and HotBird on A. To program your receiver, go to page 11, installation of a Bi-head satellite dish Astra 19, 2° + Hot Bird. Caution: you should not alter the satellite dish adjustments or the switch, it is only necessary to program your digital receiver. DiSEqC 1. 0 or Tone Burst switch Rear TouchBOX 3 Coaxial cable Scart cable 24 7 - Connection on a motorised DiSEqC 1. 2 unit already aligned Connect the cables and the leads as indicated on the figure below (figure #5). When 2 satellite receivers control the same motor, it is important that each one of them give the same number to a given satellite. For an easier installation of your new digital receiver, locate the classification of the satellites used by your previous receiver. OR Rear TouchBOX 3 Rear Analog Rear TouchBOX 3 Rear Analog Coaxial cable Scart cable figure 5 Coaxial cable Scart cable For each satellite you want to receive in digital, it is necessary to proceed as follows: Example on HotBird · Go on the reference channel (see table #1 page 9) satellite by typing the channel number then OK. · Go to MENU / Installation / Antenna Setup · On the DiSEqC Mode field, select DiSEqC 1. 2 with 34 arrow keys · Press the the red key to save. · Press the green key to access the Motor Setup menu (in the future, you won't need to do these first 4 steps, simply press the black key for direct 25 access to the Motor Setup menu ). · With 34 arrow keys, select the number of the satellite that you want to allocate to the current satellite. (Ignore the warning message) · Press OK to confirm, the motor will move to the position #1 stored in its memory. Once the motor has stopped, check that the Quality is higher than 40%. If not, it means that the motor is not correctly aligned, or that you input a wrong number. · Press EXIT until you exit all menus and check that you duly receive the channels from HotBird (or other satellites, after) Do the same procedure for the other satellites. 26 8 - Remote control description 1 Digital keys. In viewing mode, press these keys to change channel by pressing the number of the channel you want to watch. In the programming mode, these keys are used to enter the digital 2 values. Allows switching on or switching off and putting the terminal in standby. Press this key to enter in the main menu or to leave 12 the main menu. Pressing MENU in a submenu allows to exit this submenu and come back in the previous menu. 3 3VOL4 In viewing mode, press VOL key to adjust the volume. In programming mode, this key is used to alter the value of a setting. In viewing mode, press these keys to change 5 channels. [. . . ] Enter 0000 if you did not input any PIN code. If you input a PIN code, but you forgot it, contact the hotline. 37 ASSISTANCE AND ADVICE Y ou will find in the following pages, the channel parameters which we programmed in the receiver. This programming was established according to information's, which are at our disposal to date, and according to programs which are broadcast to date. The operators responsible for the television broadcasts by satellites sometimes change without notice the frequencies and the transponders, we cannot unfortunately guarantee you the exactitude of these programming in time, please accept our apologies on this matter. [. . . ]