User manual MICROTEK 710S

[. . . ] This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] GVW-1; 18AWG X 3C; SVT with national approval as UL and/or CSA approval/number(s) Europe GVDE/ÖVE and/or KEMA approval; H05VV-F 3G, 0. 75mm2, or , equivalent. The power cord should bear the name of the manufacturer and state the type of cord that it is. 2. · · · v Introduction Before installing your monitor Read this manual carefully. PAY ATTENTION to all Warning and Caution messages. DO NOT use computer components not recommended by the manufacturer. Do not attempt to service the monitor yourself. If a problem occurs, contact the manufacturer's authorized service center. About your monitor This monitor is a microprocessor-controlled color monitor that uses a TFT LCD panel. The monitor conforms to EPA Energy Star and VESA DPMS (Display Power Management Signaling) power management standards. RGB Mode This monitor is equipped with a microprocessor that identifies your computer's video mode and allows you to adjust the setting. 1 Factory-preset Modes Table 1 shows standard video mode setting that has been pre-adjusted at the factory for accurate video display. These settings are stored in the monitor's memory. Factory-preset Modes Mode NEC VGA Resolution 640 x 400 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 SVGA 800 x 600 800 x 600 800 x 600 800 x 600 XGA 1024 x 768 1024 x 768 1024 x 768 SXGA 1280 x 1024 1280 x 1024 Macintosh 640 x 480 832 x 624 1024 x 768 1024 x 768 H-Freq. (KHz) 24. 83 31. 47 31. 47 31. 47 37. 86 37. 5 35. 16 37. 88 48. 08 46. 87 48. 36 56. 47 60 63. 98 80 35 49. 7 48. 78 60. 241 V-Freq (Hz) 56. 4 70 70 60 72 75 56. 3 60. 3 72. 2 75 60 70 75 60 75 66. 7 74. 55 60 74. 927 2 Specifications Overall Dimensions (H x W x D): 16. 5 x 16. 4 x 6. 5 in. (419 x 417 x 166 mm) 14. 4 / 12 lbs 13. 3 x 10. 6in. (337. 92 x 270. 34 mm) 100 x 100mm (VESA standard) 16 million colors Gross / Net Weight Effective Display area (H/V): Wall Mount Display colors: Scan Frequencies: Horizontal Vertical Number of Pixels: Pixel pitch: Picture Tube: Power: Input Consumption 31. 47K to 80KHz 60Hz to 75Hz 1280x1024 pixels 0. 264 mm 17" TFT LCD panel 110~240 VAC (auto-sensing) Frequency: 48-62Hz 45Watts maximum (on) 1 Watt (Power saving off mode) 15-pin Mini D-sub (Standard) 1 (stereo input) 2 Video Connector Audio connector Speaker: RGB Signals: Video Sync Display Data Channel: Compatibility 3 Analog RGB 0. 7Vp-p/75W Separate VESA DDC 1/2B Operations User Controls On/Off Power Button Auto-adjustment, Brightness, Menu/Enter and & button On Screen Display, Contrast, Brightness Adjustment, H-position, V-position, Color temperature, Auto Adjustment Digital OSD (On-Screen-Display) IBM and compatibles, Apple Macintosh, NEC Control Type: Compatibility: Environmental Limits: Operating Temp. Operating Humidity Storage Humidity Agency Approval EMI Energy Saving Safety 32° to 104°F ( 0° to 40°C) -4° to 140°F (-20° to 60°C) 10 to 85% without Condensation 10 to 95% without Condensation FCC, CE EPA energy star, VESA DPMS UL/CUL, CB, TUV, BSMI 4 Installing the Monitor This monitor is equipped with an auto sensing power supply for voltage ranging from 110~240VAC, 60/50Hz. Confirm the line voltage designation on the rear panel of the monitor. To install the monitor, follow these steps: 1. Before you connect the cables, make sure that the monitor and the system unit power switches are OFF. Plug one end of the 15-pin signal cable to the monitor and the other end to the video signal connector at the rear of the system. Tighten the two screws on the cable connector on both ends. Otherwise, the screen will be abnormal and the LED light will flash yellow (and not the normal green color). Connect the power to the monitor through the AC/DC adapter. Connect the power cord on the AC outlet as shown below. 2 3 2. 3. 4. 1 5 How to use the VESA mount 1. [. . . ] Press the upper Function Control button once and then press either the upper or lower Adjustment Control button several times. If there is still no display, press the other Adjustment Control button several times. If step 2 does not work, connect your PC system to another external CRT. If your PC System functions properly with a CRT Monitor but it does not function with the LCD monitor, and the LCD monitor's power LED is blinking, the output timing of the PC's VGA card may be out of the LCD's synchronous range. [. . . ]