User manual MICROTEK GNC I SM9700XL 0402

[. . . ] ScanMaker 9700XL Installing and Getting Started Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Taking a Closer Look . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Once the scanner software installation is finished, remember to re-enable the virus protection software. For iMac users, please visit Apple's website at http://www. apple. com/imac/ to download and install any iMac updates you may require. ScanMaker 9700XL Installing and Getting Started 5 Connecting the Scanner to Your Computer The ScanMaker 9700XL comes with two built-in interfaces: USB and SCSI. You may choose any of the two interfaces to make the connection between the scanner and computer. (You should use only one interface at a time. ) Connecting using the SCSI cable Before connecting the scanner, check to see if your computer system has a built-in SCSI interface or an installed SCSI card. If you need help on installing the SCSI card, please refer to the "SCSI Installation Guide" on separate documentation included in your scanner package, or refer to the documentation that came with the SCSI card. Follow the steps below to make the SCSI connection. If the SCSI ID number 6 is used by another SCSI device, check which SCSI ID is free, and set the number to a free SCSI ID. Push the minus button (-) above the SCSI ID number to decrease the number; push the plus button (+) to increase the number. 3. Connect the scanner to your computer, using the SCSI cable. Connect one end of the SCSI cable to your computer's SCSI port, and connect the other end of the cable to the scanner's SCSI port. 6 ScanMaker 9700XL Installing and Getting Started For Macintosh users For PC users 4. Set the scanner's terminator switch to the "ON" position. Note: If you have multiple devices on your SCSI chain, make sure the scanner is the last device on the chain and that the scanner is terminated (i. e. , scanner's terminator switch is set to ON). ScanMaker 9700XL Installing and Getting Started 7 5. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). 6. Turn the scanner's power switch to "On", and wait for the green light on the scanner's front panel to stop blinking and stay on steady. 7. Turn on your computer; the system will detect the scanner automatically. 8 ScanMaker 9700XL Installing and Getting Started Connecting using the USB cable Before connecting the scanner, check to see if your computer system has a built-in USB port. The latest Macintosh computers (i. e. , G3, G4, etc. ) are equipped with a built-in USB port that is usually labeled with the USB " " logo. Follow the steps below to make the USB connection. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). Make sure no other cable is connected to the scanner except the power cord at this point. 2. Connect the scanner to your computer, using the provided USB cable. Connect one end of the USB cable to your computer's USB port, and connect the other end of the cable to the scanner's USB port. For Macintosh users USB port usually labeled with the " " logo. ScanMaker 9700XL Installing and Getting Started 9 For PC users 3. Turn the scanner's power switch to "On", and wait for the lights on the scanner's front panel to stop blinking and stay on steady. Your system will detect the scanner automatically. 10 ScanMaker 9700XL Installing and Getting Started Positioning Reflective Originals 1. Place the original to be scanned face down on the scanner's glass surface. [. . . ] From the Preview window, click the Scan Material icon, and select "Reflective". 3. From the Settings window, click on the Scanner Profile list box and select the profile you have just created. 16 ScanMaker 9700XL Installing and Getting Started Specifications Scanning Modes Color, grayscale, and black-and-white in a single scanning pass 48-bit color input and output (approx. 281 billion colors) 16-bit grayscale (approx. 65, 536 shades of gray) Scanning area Resolution Reflective: 12" x 17" (305 x 431. 8 mm) Optical: 1200 dpi x 2400 dpi Interpolated: 9600 dpi x 9600 dpi 24. 7" x 14. 8" x 5. 1" (627. 38 x 375. 92 x 129. 54 mm) 26. 4 lbs (12 kg) AC 100V to 240V, 47-63 Hz Operating temperature: 50° to 104°F (10° to 40°C) Relative humidity: 20% to 85% Dimensions (L x W x H) Weight Voltage Environment Additional Documentation in the CD-ROM Additional documentation is provided in the Microtek CD-ROM that contains ScanWizard Pro, Scanner ICC Profiler, troubleshooting, etc. [. . . ]