User manual MICROTEK GNC I SM9800XL 1201

[. . . ] ScanMaker 9800XL Installing and Getting Started Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Unpacking the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Taking a Closer Look . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This port should be designated with the FireWire symbol shown to the left. · For PC users, the FireWire card should be installed and work properly in your computer. System is Not FireWire-ready If your system is not FireWire-ready, you will need to install a FireWire card. For more details on how to install the FireWire card, please refer to the "FireWire Installation Guide" on a separate documentation included with your scanner package. Alternatively, you can use the USB or SCSI interface to connect your scanner. For FireWire-ready systems: Follow the steps below to make the FireWire connection. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). Make sure no other cable is connected to the scanner except the power cord at this point. 6 ScanMaker 9800XL Installing and Getting Started 2. Connect the scanner to your computer, using the provided FireWire cable. Connect one end of the FireWire cable to your computer's FireWire port, and connect the other end of the cable to the scanner's FireWire port. For Macintosh users The latest Macintosh computers (i. e. , G3, G4, etc. ) are equipped with a built-in FireWire port, usually labeled with the " " logo. For PC users 3. Turn the scanner's power switch to "On", and wait for the green light on the scanner's front panel to stop blinking and stay on steady. 4. Your system will detect the scanner automatically. ScanMaker 9800XL Installing and Getting Started 7 Using the SCSI cable Before connecting the scanner, check to see if your computer system has a built-in SCSI interface or an installed SCSI card. If you need help on installing the SCSI card, please refer to the "SCSI Installation Guide" on a separate documentation included with your scanner package, or refer to the documentation that came with the SCSI card. Follow the steps below to make a SCSI connection. If the SCSI ID number 6 is used by another SCSI device, check which SCSI ID is free, and set the number to a free SCSI ID. Push the minus button (-) above the SCSI ID number to decrease the number; push the plus button (+) to increase the number. 3. Connect the scanner to your computer, using the SCSI cable. Connect one end of the SCSI cable to your computer's SCSI port, and connect the other end of the cable to the scanner's SCSI port. For Macintosh users 8 ScanMaker 9800XL Installing and Getting Started For PC users 4. Set the scanner's terminator switch to the "ON" position. Note: If you have multiple devices on your SCSI chain, make sure the scanner is the last device on the chain and that the scanner is terminated (i. e. , scanner's terminator switch is set to ON). ScanMaker 9800XL Installing and Getting Started 9 5. Plug the power cord into the back of the scanner, and plug the other end into a power source (power surge protector highly recommended). 6. Turn the scanner's power switch to "On", and wait for the green light on the scanner's front panel to stop blinking and stay on steady. 7. Turn on your computer; the system will detect the scanner automatically. 10 ScanMaker 9800XL Installing and Getting Started Using the USB cable Before connecting the scanner, check to see if your computer system has a built-in USB port. The latest Macintosh computers (i. e. , G3, G4, etc. ) are equipped with a built-in USB port, and usually labeled with the USB " " logo. Follow the steps below to make the USB connection. [. . . ] From the Preview window, click the Scan Material icon, and select the "Reflective" icon. 3. From the Settings window, click on the Scanner Profile list box and select the profile you have just created. 18 ScanMaker 9800XL Installing and Getting Started Specifications Scanning Modes Color, grayscale, and black & white in a single scanning pass 48-bit color input and output (approx. 281 billion colors) 16-bit grayscale (approx. 65, 536 shades of gray) Scanning area Resolution Reflective: 12" x 17" (305 x 431. 8 mm) Optical: 1600 dpi x 3200 dpi Interpolated: 12800 dpi x 12800 dpi 24. 7" x 14. 8" x 5. 1" (627. 38 x 375. 92 x 129. 54 mm) 26. 4 lbs (12 kg) AC 100V to 240V, 47-63 Hz Operating temperature: 50° to 104°F (10° to 40°C) Relative humidity: 20% to 85% Dimensions (L x W x H) Weight Voltage Environment Additional Documentation in the CD-ROM Additional documentation is provided in the Microtek CD-ROM that contains ScanWizard Pro, Scanner ICC Profiler, troubleshooting, etc. [. . . ]