User manual MICROTEK GNC I SMI700 3656B

[. . . ] Installing your Microtek ScanMaker i700 Important: Do not remove the yellow stickers from your scanner until you are told to do so. You must install software before connecting your scanner. Open your scanner package and check the components. If any component is missing, call Microtek Customer Service. 1 6 4 7 2 5 8 10 9 3 11 1. Hi-Speed USB cable (backward compatible with USB 1. 1) 4. [. . . ] To select the film you wish to scan, make sure that the FilmView is on, then place the film you wish to scan on the top of the scanner lid (Light Plate), using the light source provided by the FilmView to preview your film. Note: If the light source of the FilmView is in the "Sleep" mode, press the scanner's Custom button to exit or halt sleep mode. For more details on the Custom button, see the online help of the Microtek Scanner Configuration (MSC). To run auto-crop, the following conditions should all be met: · The operating system is either Windows or Mac OS X. · The correct EZ-Lock film holder is loaded and correctly aligned on the scanner surface. · The scan material is Positive or Negative Film. · In the Scan Job Queue window, the "Multiple Auto-crop for EZ-Lock Film Holder" option is checked. 10 ScanMaker i700 Installing and Getting Started A. Using the EZ-Lock 35mm Filmstrip Holder The EZ-Lock 35mm Filmstrip Holder can simultaneously hold two strips of 6 frames each, or a total of 12 frames. Load the filmstrip face down inside the holder. Slide the filmstrip along the slots of the holder until the filmstrip is fully loaded. Align the frame-by-frame partition with the dash marks on the film guide. For a short filmstrip, make sure the film edge is close to the open end of the slot. 2. Raise the scanner lid, then place the holder with the loaded film on the scanner glass surface, as shown in the illustration. To make sure the auto multiframe cropping feature performs correctly, align the holder's front edges flush against the top ruler of the scanner. The calibration window on the glass surface should be kept clear and free from any obstruction during scanning. 3. Gently lower the scanner lid down onto the scanner glass surface; the lid should be able to close completely. Double-click the ScanWizard 5 icon ( ) on your desktop to launch the ScanWizard 5 Standard Control Panel, then click the Switch icon ( )on the right corner of the Standard Control Panel to switch to the Advanced Control Panel. Click the Scan Material button ( ), and choose Negative Film. For Mac OS X, select Negative from the Scan Material drop-down menu. ScanMaker i700 Installing and Getting Started 11 6. Check the "Multiple Auto-crop for EZ Lock Film Holder" option in the Scan Job Queue window. Click the Overview button to auto-crop and perform a preview of the film loaded onto the scanner. When done, you will see multiple scan frames that have been automatically cropped in the preview window. Multiple job titles will appear in the Scan Job Queue window, numbered sequentially and all marked by a "Check" that indicates the jobs are ready to be scanned. The scan area (framed in dotted lines) will appear in the Preview window. Maximum scanning range is 9" x 4". Auto-cropped images are framed in dotted line. 8. Specify your scanning parameters in the Settings window. Click the Scan to button to scan all the checked jobs. [. . . ] - Launch Application: Defines an application to be launched. 20 ScanMaker i700 Installing and Getting Started System Requirements · CD-ROM drive (for installing software) · Color display with 24-bit color output capability · 128MB RAM (256MB or more to use DIGITAL ICE Technology) PC and compatibles · · Pentium III PC or higher with USB, Hi-Speed USB (USB 2. 0), or FireWire (IEEE 1394) port Microsoft Windows 98SE, Me, 2000 or XP Macintosh · iMac or Mac G3/G4/G5 with built-in USB port or FireWire port · Mac OS 9. x, Mac OS X 10. 2, 10. 3 or later Specifications Scanning Modes Color, grayscale, and black-and-white in a single scanning pass True 48-bit color (approx. 281 x 1012 colors) 16-bit grayscale (approx. 65, 536 shades of gray) Scanning Area Reflective: 8. 5" x 14" (216 mm x 356 mm) Transparent: 4" x 9" (102 mm x 229 mm) Resolution Optical: 9600 dpi x 4800 dpi Interpolated: 65, 535 dpi (PC); 32, 767 dpi (Mac) Interface Hi-Speed USB (USB 2. 0) and FireWire (IEEE 1394) Dimensions (L x W x H) 21. 5" x 11. 7" x 3. 6" (545 mm x 297 mm x 92 mm) Net Weight 11. 9 lbs (5. 4 kg) Voltage AC 100V to 240V 1. 2A Max; 47-63 Hz (Input) 15V/2. 5A (Output) Environment Operating Temperature: 50° F to 104° F (10° C to 40° C ) Power supply Manufacturer Model No. Voltage (AC/DC adapter) FAIRWAY VE50-150A 100V to 240V ScanMaker i700 Installing and Getting Started 21 22 ScanMaker i700 Installing and Getting Started Federal Communications Commission Interference Statement This equipment (Model: MRS-9600FU2) has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. [. . . ]