User manual MICROTEK GNC I SMI700 3848A

[. . . ] Purpose ­ Sets the image resolution to match your target application. NOTE: Click the Scale Output, Adjust, and Reset buttons if you need to make further adjustments. NOTE: To lock the scanner (for shipping and other reasons), tilt the back left corner of the scanner to see the locking switch at the bottom. Next, push the locking switch to the "Locked" position. Do not turn the scanner upside down and attempt to lock the scanner this way, as this may damage the scanner. Microtek International, Inc. I49-003848 A FireWire cable Hi-Speed USB cable EZ-Lock Film Holders For details on how to use the Advanced Control Panel, refer to the ScanMaker i700 Supplement. Connect Scanner Power cord Software CDs Power adapter To the scanner lid Make sure the scanner lid (with built-in transparency adapter) is properly installed, with its connector securely connected to the scanner's 15-pin accessory port. Install Software Important: Do not remove the yellow stickers from your scanner until you are told to do so. [. . . ] Since this is your first install and you have not yet connected the scanner, simply ignore the message that appears and proceed to the next step. To the Hi-Speed USB cable D. Connect one end of the Hi-Speed USB cable to your computer. Connect the other end of the Hi-Speed cable to the scanner's USB port. Press the power button at the front panel of your scanner, and wait for the lights to stop blinking and stay on steady. The system will detect your scanner automatically. Power button F · NOTE: If your computer has both Hi-Speed USB (USB 2. 0) and USB 1. 1 ports, connect the cable to the Hi-Speed USB port. Use the USB 1. 1 port only if your computer does not have Hi-Speed USB. Also, refer to the ScanMaker i700 Supplement for details on how to connect the scanner using the FireWire port. TURN OVER TO CONTINUE Using the Film Holders A. Load the film inside the holder, with the film's shiny base facing down. Using DIGITAL ICE and ColoRescue 4. Click the Scan Material button in the ScanWizard Preview window. Choose "Negative" or "Negative Film" to scan negative film, or choose "Positive" or "Positive Film" to scan transparencies and slides. Manuals If you have additional questions and need further instruction or information, we provide PDF manuals for: 1. Using the ScanWizard 5 scanning software EZ-Lock 35mm Filmstrip Holder Mac OS X Windows XP 2. Using the bundled third-party software To access the PDF manuals: Insert the Microtek CD-ROM into your computer's CD-ROM drive. Next, locate and click the "View Manuals" option when the software installer window appears on your screen. Finally, select and click the title of the manual you wish to view. 5. In the ScanWizard Settings window, verify the DIGITAL ICE strength setting. "Normal" is sufficient in most cases. Missing Items If your package is missing items, please call the number below. Customer Service Department 310-687-5940 Hours (PST): Mon, Tues, Web, Fri 7am-5pm; Thurs 7am-3pm EZ-Lock 35mm Slide Holder Reconstructing Damaged Photos and Film The DIGITAL ICE feature repairs cracks, tears, and rips in your damaged photos and film. Raise the scanner lid, and place the photo on the scan bed. Black Mat 24-hour Online Technical Assistance 6. Click the "Scan to" button in the Preview window. DIGITAL ICE will automatically repair the damaged film. For free 24-hour technical assistance, Microtek offers automated technical support via the Internet and Email. · · World Wide Web www. support. microtek. com Personal Email Support www. support. microtek. com/emailsupport/ Automated Email Responder helpdesk@support. microtek. com EZ-Lock 4" x 5" / 6 x 9 cm (120) Film Holder Make sure the Black Mat is attached to the scanner lid, so that uneven photos lay as flat as possible. [. . . ] Do not block the calibration area (as indicated in the "Using the Film Holders" section). From the ScanWizard 5 Standard Control Panel, go to the Original button category, then proceed to the Film subcategory and make sure you select either the Positive or Negative option. Third-Party Software Assistance For technical support or any questions you have on these software titles which may be included with your package, please use the contact information listed below. Phone ABBYY® FineReader® Sprint Adobe® Photoshop® Elements Adobe® Photoshop® Album SE Adobe® Acrobat® Reader Ulead Photo Explorer ® TM Website www. abbyyusa. com 510-226-6719 800-87-ADOBE 310-896-6391 www. adobe. com www. ulead. com B. Remove the Black Mat: Raise the scanner lid, and push the Black Mat to the side to remove it from the scanner lid. Off Scanner is off. First, make sure that you have followed installation steps 1 through 4. [. . . ]