User manual MICROTEK GNC M 715C 0606

[. . . ] USER'S MANUAL www. microtek. com FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. [. . . ] LCD · Periodic cleaning with a soft dry cloth is recommended. · Do not use tissue to clean the LCD screen, as this may damage the screen. 3 Installation Installing the Monitor · DO NOT install the monitor where sudden temperature changes may occur, or in humid, dusty, or smoky areas as fire, electric shock or damage may ensue. · DO NOT place your LCD monitor near a window as it may be severely damaged if exposed to rain, water, moisture, or sunlight. · MAINTAIN good ventilation; covering of ventilation slots or holes may cause fire. · PLACE the monitor at least 4 inches (or 10 cm) away from the walls · SAFE storage temperature of the LCD monitor is in a range of ­4ºF to +149ºF (-20ºC to +65ºC). 4 Connecting the Monitor Warning: Do not operate the LCD monitor with unspecified power supply. Usage of incorrect voltage will cause the unit to malfunction and may cause fire or electric shock. From the box, take out the monitor and place on the table, with the front side facing down. Note: To prevent damaging or scratching the LCD monitor, always keep the surface of the table clean or covered with a soft cloth when handling the monitor. Plastic rear cover 3. From the rear view of the LCD monitor, disengage and remove the plastic back cover from the stem. Stem 4. Tilt the stem slightly to a slanting upright position (max. Thread the VGA connector of the VGA cable through the hole of the stem, then connect it to the LCD monitor's VGA port. Thread the DC connector of the adapter through the hole of the stem, then plug it to your monitor's DC jack. Make sure the cables are securely connected. 5 7. Engage the plastic rear cover back on the top of the stem. 8. Connect the other end of the VGA cable to your computer's VGA port. Plug the power cord's female end into the AC adapter, and plug the male end into a wall outlet or power source. Turn on your computer, and then turn on your LCD monitor. AC/DC Adapter VGA cable Power cord Note: For added protection, the use of a Surge Protection device is recommended. The Surge Protection device should be installed between the AC Adapter and the electrical wall outlet to prevent the effects of sudden current variations from reaching and damaging the LCD monitor. 6 Adjusting the Viewing Angle Your LCD monitor is designed to allow adjustment for optimal viewing angles. You can adjust the monitor upward to 25 degrees and downward to -3 degrees. Note: Do not touch the screen while changing the viewing angle, as this may damage the screen. In addition, make sure your fingers do not get caught in any of the monitor's parts while adjusting the viewing angle. 7 Operating the Monitor The LCD monitor has been preset at the factory with the Timing shown in the "Appendix B" section to achieve optimal display. You can adjust the display to the desired brightness and sharpness by following the instructions below. Buttons AUTO Functions Automatically adjusts image Clock, Phase, H-Position, V-Position settings Indicates cursor movement, or decreases the values of a setting when manually operating the OSD MENU Displays the OSD main menu or enters a submenu Indicates cursor movement, or increases the values of a setting when manually operating the OSD EXIT Saves or cancels a user setting, then exits the OSD menu Power Switch Powers the monitor ON/OFF Green ­ Normal operation mode Amber ­ Power management mode How to Use the OSD (On-Screen Display) The OSD lets you easily adjust the various settings for your LCD monitor to desired levels of performance. The OSD includes a main menu and various submenus. Main Menu Submenu User Setting 8 Operating Procedure The buttons on the right side of the Control Panel are used to navigate the OSD. Follow the sequence below to do the following: Navigate the OSD menu item, go through the submenus, select a setting, save or cancel the setting, and finally exit the OSD item. [. . . ] If the cables are damaged, they may cause fire or electric shock. STOP OPERATING THE MONITOR IMMEDIATELY WHEN YOU DETECT ANY ABNORMAL OCCURRENCE If you notice any abnormal phenomenon such as strange noises, smoke, or unusual smells, unplug the monitor and contact your dealer or the nearest service center immediately. DO NOT REMOVE THE CABINET Removing the cabinet may expose you to the danger of fire or electric shock. DO NOT PUT ANY FOREIGN OBJECT INSIDE THE MONITOR Operating the monitor with foreign objects inside may cause fire, electric shock, or damage. [. . . ]