User manual MICROTEK GNC M 815C 0302

[. . . ] iii · Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. iv Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n'èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. " ENERGY STAR This product meets the Energy Star guidelines for energy efficiency. TCO'99 Congratulations! [. . . ] LCD Periodic cleaning with a soft dry cloth is recommended. It may damage the LCD screen. 5 Chapter 2 Installing the Monitor DO NOT install the monitor where sudden temperature changes may occur, or in humid, dusty, or smoky areas as it may cause fire, electric shock or damage. DO NOT place your LCD Monitor near a window as it may be severely damaged if exposed to rain, water, moisture, or sunlight. MAINTAIN good ventilation; covering of ventilation slots or holes may cause fire. PLACE the monitor at least 4" (or 10 cm) way from the walls SAFE storage temperature of the LCD Monitor is in a range of -20 to +65ºC. 6 Connecting the monitor 1. Turn off your PC and the LCD Monitor before connecting your LCD monitor to the PC. Use VGA cable to connect the VGA connector of the LCD Monitor to the VGA port of the PC system. Make sure the cable head is securely connected. (Option: If your system is Dual signal model, then use the DVI cable to connect the DVI connector to the DVI port). Use Audio cable to connect "Audio in" jack on LCD Monitor and sound card's "Audio out" jack. Plug the DC connector of the adaptor to your monitor's DC jack. Plug the female end of the power cord into the AC adaptor. Connect the male end of the power cord into a wall socket. Turn on your computer, and then turn on your LCD Monitor. 7 NOTE: For added protection, it is recommended to use a Surge Protection device plugged between the AC Adapter and the electrical wall outlet to prevent the effects of sudden current variations from reaching the LCD Monitor. Sudden peaks of Audio in VGA connector Power DVI connector (optional) Connect with Audio cable. Connect with detachable DVI cable Remark: DVI Cable is for Dual Model use only electricity may cause damage to the Monitor. Adjusting the Viewing Angle Your LCD Monitor is designed to allow you to adjust it to an optimal viewing angle. NOTE Do not touch the screen while changing the viewing angle. Make sure not to catch your fingers while changing the viewing angle. 8 Chapter 3 Operating the Monitor Buttons 1 2 3 4 5 Functions Automatically adjust image Clock, Phase, H-Position, V-Position settings Indicating the cursor movement or OSD manual selection in decremental values Pop up OSD Menu or Enter into sub menu Indicating the cursor movement or OSD manual selection in incremental values Exit OSD Menu and user setting saving Power ON/OFF the monitor/ Green ­ Normal operation Amber ­ Power Management 9 AUTO MENU EXIT Power Switch 6 How to Use the OSD (On Screen Display) OSD function allows the user to easily adjust the display to the desired quality. The OSD menu includes a main menu and a sub-menu. Structure of OSD Menus Operating Procedure Use the buttons on the right side control panel to adjust the OSD 1. Press "MENU" button to pop up the OSD menu. Press " " or " " button to select menu item. [. . . ] When using the monitor over a prolonged period of time, a ten-minute-break per hour is recommended. 16 SPECIAL NOTES ON LCD MONITORS The following are normal with LCD monitors and do not indicate a problem. When first turning on the LCD monitor, if the picture does not fit in the display area, it is because of the type of computer that is used. In such case, adjust the picture position to its correct position. (See Operating the Monitor) The screen may flicker during initial use. Turn off the power switch and then turn it on again the flickering should disappear. Users may notice a little uneven brightness on the screen depending on the desktop pattern they use. [. . . ]