User manual MICROTEK GNC M ATX6000XY XXXX

[. . . ] 1 Introduction Congratulations on your purchase of the ArtixScan 6000XY scanner. The 42-bit highresolution ArtixScan 6000XY is specifically for graphic arts and imaging professionals. This manual will help you in the installation and operation of your scanner. Specifications Type Image Sensor Mechanical Resolution Optical Resolution Sample Depth Dynamic Range Scanning Area Desktop, XY technology scanner Tri-linear 8, 000 element CCD 6, 000 dpi 2, 000 dpi 14 bits per color 3. 7D Reflective 1 " x 1 " (305 mm x 432 mm) :2 7 Tr ansparency: 1 " x 1 " (305 mm x 432 mm) 2 7 15 scans per hour (6 cm x 7 cm, 250%, 300dpi, CMYK) SCSI-2 Cold Cathode Lamp Opera i g 61 - 80°F (16 - 27°C) tn: Storage: -10 - 55°F 10% - 85% 14" x 34" x 27. 5" (36 mm x 87 mm x 70 m 147 lb (67 kg) Opera i n 290 W to: Standby 200W : CSA, T U V, FCC class B, CF Scanning Productivity Itr n e face Lamp Source Temperature Humidity Dimensions Net W eight Pow er Consumption Cert f c t o s iiain ArtixScan 6000XY Installation and Operation Manual 1 2 Site Power and Working Space This section describes the working conditions and working space for operating the ArtixScan 6000XY. General Requirements Before unpacking your scanner, make sure that the site where the scanner will be installed is big enough to allow for easier operation. · Make sure that the operating environment for the scanner is free of dust and other contaminants. [. . . ] Make sure the jigsaw edges of the 2 holders interlock. See the figure below. The two guide-holes. 14 ArtixScan 6000XY Installation and Operation Manual · Place the mask on the scan bed. Place the mask. The figure below shows the customized mask with cut windows for 5 transparencies. 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 1 9 8 7 6 5 4 3 2 0 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 7 6 5 4 User mask name si ency em ul on si do r de w r n Tape t anspa 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 3 1 Do not cover bar-code Customized mask with cut windows fo 5 r t ansparencies. r 19 20 21 22 2 23 24 25 26 27 28 29 30 31 32 33 34 35 TR A N S P A R E N C Y S I E D 36 USER DEFINED MASK 37 38 39 Cat. 509D1L005 40 41 4 42 43 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 1 9 8 7 6 5 4 3 · Mount the mask without originals in the scanner with the transparency side facing up; insert the mask's registration holes into the registration pins of the scan bed. ArtixScan 6000XY Installation and Operation Manual 2 0 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 15 Note: The 0, 0 corner of the mask is approximately above the 0, 0 corner of the scan bed. For the reflective material: · Tape the reflectives to the reflective side of the mask, according to your customized format. Taping the originals is similar to directly place your original on the scan bed. Make sure not to cover the barcode windows. · To mount in the scanner, turn the mask over so that the transparency label of the mask faces up. Align and insert the mask registration holes into the registration pins of the glass. Tr ansparency side Transparency side Align and insert the mask r g s ration holes. eit Using the customized mask (Note: This section should work with the software, so presently it is left blank. ) Using the slide holder The slide holder can hold up to 20 pieces of 35mm slides. We recommend you insert your slides row by row, that means, when the first row is full, continue to the next row. Insert t e s i e r by r h l d s ow ow. 16 ArtixScan 6000XY Installation and Operation Manual Appendix A: Service and Maintenance This appendix discusses regular maintenance which covers scanning lamp replacement and glass plate cleaning. Lamp Replacement Your ArtixScan 6000XY scanner consists of 3 scanning lamps: · One scanning lamp in the transparency scanning carriage (inside the scanner's top cover) · Two scanning lamps in the reflective scanning carriage In the following situations you should replace the scanning lamps: · The light level is low. This rule applies to both the transparency and reflective scanning lamps. · The scanning lamp does not light up. Replacing the Transparency Scanning Lamp 1. Wait a few minutes for cooling off scanning lamp. Lift the top cover up. Lf tetpc r i t h o ove up. Note: In operation, we recommend you place cardboard on the scan bed to prevent damaging the glass. Unscrew the 4 screws which holds the 4 corners of the top cover. When unscrewed, the screws sprint out a little, there is no need to remove the screws. ArtixScan 6000XY Installation and Operation Manual 17 Tu the screw counterclockwise rn to unscrew. 4. Note: Make sure the cover is closed properly. Remove the top cover by holding the two diagonal corners, then lift it. L f t e t p c r. i t h o ove When the top cover is removed, the scanning lamp can be visually inspected. Inspect the scanning lamp. 18 ArtixScan 6000XY Installation and Operation Manual 6. To remove the scanning lamp, first gently pull one end of the lamp inward. Pull the scanning lamp out. 7. To insert the new scanning lamp, follow these guides: · · · · · Make sure when inserted, the lamp with the lamp window facing down. [. . . ] Solution: This problem arises when one of the scanner switches is activated. · Power off your scanner, two minutes later, turn it back on. After 30 seconds, visually inspect whether the Status lamp stays steady green light. · Check that the scan bed glass, front panel, and top cover are installed correctly. 26 ArtixScan 6000XY Installation and Operation Manual 2. [. . . ]